Jv3 error 23

jv3 error 23

Fixing Mimaki JV3-160SP Error Codes list · Code: 23 · Display: ERROR23 HOST I/F · Description: •A time limit exceeded error occurred in communication between the. The JV3-75SPII/130SPII is a color ink-jet printer applicable to high quality printing ERROR 23. HOST I / F. ERROR 24. I / F INITIAL. ERROR 30. OPERATION. c/o Error! NCC JV3 - Verification using a reference building. 13-23 Gibbons Street, Redfern, NSW 2016 – Source: Google Map.

Jv3 error 23 - valuable message

Error message

ERROR 23

HOST I / F

ERROR 24

I / F INITIAL

ERROR 30

OPERATION

ERROR 34

DATA REMAIN

ERROR 40

MOTOR X

ERROR 41

MOTOR Y

ERROR 42

X CURRENT

ERROR 43

Y CURRENT

ERROR 46

WIPER

ERROR 50

MEDIA SENSE

ERROR 51

Y ORIGIN

ERROR 57

HEAD HIGHT SENS.

Cause

HOST I/F Timeout error has

arisen during communication

between the host computer

and interface board.

Initial operation failure of the I/

F board and control board.

An error occurs on the inter-

face between the I/F board

and the control board.

Settings for functions have been

tried to be changed though there

remains received data that has

not yet been printed.

The Xmotor has been overload.

The Ymotor has been overload.

Overcurrent error on the

Xmotor has been detected.

Overcurrent error on the

Ymotor has been detected.

The wiper position is not

correct.

Paper could not be detected.

The media set position or

media itself is not correct.

Origin could not be detected.

Head height could not be

detected.

- 6.10 -

Corrective measure

Check to be sure that the cable

is securely connected to the

host computer and interface

board. Also, check to ascertain

that no error has arisen on the

host computer side.

Turn off the power to the device

and turn it on after a while. If the

same error message appears

again on the LCD, contact your

local distributor to call for service.

Perform a proper operation.

Print all pieces of received

data or execute the data clear

function. Then, change the

settings.

Turn off the power to the

device and turn it on after a

while. If the same error

message appears again on the

LCD, contact your local dis-

tributor to call for service.

Refer to "Setting the media".

page 2.8.

If this error cannot be resolved

even after setting it correctly,

contact the dealer.

Turn off the power to the

device and turn it on after a

while. If the same error

message appears again on the

LCD, contact your local dis-

tributor to call for service.

Mimaki JV3-160SP Error Codes and quick guides [Solved]

Fixing Mimaki JV3-160SP Error Codes list

– Compatible Printer model: Mimaki JV3-160SP
– Mimaki JV3-160SP Error Code description:

  • Code: 01
  • Display: ERROR01 MAIN ROM
  • Description: • The control ROM is in abnormal conditions.
  • Troubleshooting Guides: 1) Replace the main PCB with a new one.
  • Code: 02
  • Display: ERROR02 MAIN RAM
  • Description: • The control RAM is in abnormal conditions.
  • Troubleshooting Guides: 1) Replace the main PCB with a new one.
  • Code: 03
  • Display: ERROR03 POWER +5V POWER +35V
  • Description: • The +5V (+35V) voltage is in abnormal conditions.
  • Troubleshooting Guides: 1) Replace the power supply or the main PCB with a new one.
  • Code: 04
  • Display: ERROR04 FLASH ROM
  • Description: • The Flash memory is in abnormal conditions.
  • Troubleshooting Guides: 1) Replace the main PCB with a new one.
  • Code: 06
  • Display: ERROR06 D-RAM
  • Description: • An error has occurred in the D-RAM.
  • Troubleshooting Guides: 1) Replace the main PCB with a new one.
  • Code: 07
  • Display: ERROR07 TEMP n
  • Description: • Abnormal temperature is detected.
  • Troubleshooting Guides: 1) Has ink in the camper run out? 2) Check the FPC cable connection. 3) Replace the Slider PCB with a new one. 4) Replace the head with a new one. 5) Replace the main PCB with a new one.

Mimaki JV3-160SP error code

  • Code: 08
  • Display: ERROR08 ENCODER
  • Description: • The Linear encoder is in abnormal conditions.
  • Troubleshooting Guides: 1) Replace the Linear encoder with a new one. 2) Replace the main PCB with a new one.
  • Code: 09
  • Display: ERROR09 HDC
  • Description: • Configuration of PDC/IOC has not been successfully carried out. •Configuration of HDC has not been successfully carried out.
  • Troubleshooting Guides: 1) Replace the main PCB with a new one.
  • Code: 10
  • Display: ERROR10 COMMAND
  • Description: •Command code other than MRL has been received.
  • Troubleshooting Guides: 1) Check the data received through HEX dump. 2) If error occurs at 1394 a. Check Time out of the transfer tool (RIP). b. Replace the I/F connection board with [E102154A] or later. c. Replace the 1394 board with a new one. d. Replace the main PCB with a new one. e. Supply power to the 1394 PCI board in the PC through the power cable.
  • Code: 11
  • Display: ERROR11 PARAMETER
  • Description: • Parameter that has not defined in MRL has been received.
  • Troubleshooting Guides: 1) Check the data received through HEX dump. 2) If error occurs at 1394 a. Check Time out of the transfer tool (RIP). b. Replace the I/F connection board with [E102154A] or later. c. Replace the 1394 board with a new one. d. Replace the main PCB with a new one. e. Supply power to the 1394 PCI board in the PC through the power cable.
  • Code: 12
  • Display: ERROR12 Ment Command
  • Description: •A command error for manufacture of has occurred.
  • Troubleshooting Guides: 1) It is not used in the field
  • Code: 20
  • Display: ERROR20 I/F BOARD
  • Description: •A error occurred in communication between the main PCB and the interface board.
  • Troubleshooting Guides: 1) Replace the I/F PCB with a new one. 2) Replace the main PCB with a new one. 3) Replace the I/F connection board with a new one. 4) Supply power to the 1394 PCI board in the PC through the power cable.

– Mimaki JV3-160SP Error codes and solution steps to solve problems:

  • Code: 21
  • Display: ERROR21 I/F NONE
  • Description: • The I/F board could not be recognized.
  • Troubleshooting Guides: 1) Is the I/F board mounted correctly?
  • Code: 23
  • Display: ERROR23 HOST I/F
  • Description: •A time limit exceeded error occurred in communication between the host computer and the interface board.
  • Troubleshooting Guides: 1) Is the cable loose? 2) Has an error occurred on the host computer? 3) Is the application being used running normally?
  • Code: 24
  • Display: ERROR24 I/F INITIAL
  • Description: • The I/F board is in abnormal conditions.
  • Troubleshooting Guides: 1) Replace the I/F PCBwith a new one. 2) Replace the main PCB with a new one. 3) Replace the main PCB with a new one.
  • Code: 30
  • Display: ERROR30 OPERATION
  • Description: • Improper operation has been performed.
  • Troubleshooting Guides: 1) Indicate the improper operation. 2) Replace a key board. 3) Replace a main PCB.
  • Code: 34
  • Display: ERROR34 DATA REMAIN
  • Description: • Operating condition is tried to be changed when data that has not yet been plotted remains.
  • Troubleshooting Guides: 1) This tells that any of the operating conditions cannot be changed if data that have not been plotted remains.
  • Code: 40
  • Display: ERROR40 MOTOR X
  • Description: • The X-axis motor has been overloaded.
  • Troubleshooting Guides: 1) Replace X axis motor. 2) Replace a main PCB.
  • Code: 41
  • Display: ERROR41 MOTOR Y
  • Description: • The Y-axis motor has been overloaded. • The brush of motor is in abnormal conditions.
  • Troubleshooting Guides: 1) Clean the main guide axis. 2) Replace Y axis motor. 3) Replace a main PCB.
  • Code: 42
  • Display: ERROR42 X CURRENT
  • Description: • Overcurrent error has arisen on the X-axis motor
  • Troubleshooting Guides: 1) Replace X axis motor. 2) Replace a main PCB.
  • Code: 43
  • Display: ERROR43 Y CURRENT
  • Description: • Overcurrent error has arisen on the Y-axis motor
  • Troubleshooting Guides: 1) Replace Y axis motor. 2) Replace a main PCB.
  • Code: 46
  • Display: ERROR46 WIPER
  • Description: • The wiper-control is in abnormal conditions.
  • Troubleshooting Guides: 1) Turn on the power. 2) Replace a wiper assy. 3) Replace IO PCB. 4) Replace a wiper sensor. 5) Replace a wiper motor.
  • Code: 50
  • Display: ERROR50 MEDIA SENSE
  • Description: • Media detection has not been successfully carried out.
  • Troubleshooting Guides: 1) Make sure that there is no gap between platen F (aluminum) and the edge of the P cover F rubber. If there is a gap, stick the rubber appressed against the platen. The gap may be detected in mistake. 2) Make sure that platen cover F is fixed securely using the platen cover F mounting screws (attached on auxiliary side plates R and L to prevent the cover from protruding). 3) Check if the media right edge is set at a position 15mm or more from the rightmost edge of the rightmost feed roller:R1 toward the station side or not. 4) Cleaning or replace a paper width sensor. 5) Replace a HDC FPC cable. 6) Replace a slider PCB. 7) Replace a main PCB.
  • Code: 51
  • Display: ERROR51 Y ORIGIN
  • Description: • Y-axis origin detection has not been successfully carried out.
  • Troubleshooting Guides: 1) Replace a Y axis motor. 2) Replace a Y origin sensor. 3) Replace a IO PCB. 4) Replace a main PCB.

Waste Ink Pad Counter Utility Functions:

– Cleaning printhead.
– Ink charge.
– Fix Epson red lights blinking Error

Epson red lights blinking 2

– Fix Epson Service Required Error: A printer’s ink pad at the end of its service life Please contact Epson Support.
Epson red lights blinking 2

– Check the current value of waste ink counters and ink level counters.
– Clear Waste Ink Counters.
– Read and write serial number.
– Read and write USB ID.
– Read and write HEAD ID.
– Make EEPROM dump, backup.
– Paper feed test.
– Nozzle check.
– Color check pattern.
– Initialize (disable) PF deterioration offset.
– Retrieve device information

Contact us to get support with Mimaki JV3-160SP Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/

Filed Under: error code, MimakiTagged With: fix Mimaki JV3-160SP, Mimaki JV3-160SP Error, Mimaki JV3-160SP repair service, Mimaki JV3-160SP troubleshooting

We have noticed an unusual activity from your IP 62.89.30.2 and blocked access to this website.

Please confirm that you are not a robot.

Error message

ERROR 23

HOST I / F

ERROR 24

I / F INITIAL

ERROR 30

OPERATION

ERROR 34

DATA REMAIN

ERROR 40

MOTOR X

ERROR 41

MOTOR Y

ERROR 42

X CURRENT

ERROR 43

Y CURRENT

ERROR 46

WIPER

ERROR 50

MEDIA SENSE

ERROR 51

Y ORIGIN

ERROR 57

HEAD HIGHT SENS.

Cause

HOST I/F Timeout error has

arisen during communication

between the host computer and

interface board.

Initial operation failure of the I/F

board and control board.

An error occurs on the interface

between the I/F board and the

control board.

Settings for functions have been

tried to be changed though there

remains received data that has not

yet been printed.

The Xmotor has been overload.

The Ymotor has been overload.

Overcurrent error on the Xmotor

has been detected.

Overcurrent error on the Ymotor

has been detected.

The wiper position is not

correct.

Paper could not be detected.

The media set position or media

itself is not correct.

Origin could not be detected.

Head height could not be

detected.

- 6.9 -

Corrective measure

Check to be sure that the cable is

securely connected to the host

computer and interface board.

Also, check to ascertain that no

error has arisen on the host

computer side.

Turn off the power to the device

and turn it on after a while. If the

same error message appears again

on the LCD, contact your local

distributor to call for service.

Perform a proper operation.

Print all pieces of received data or

execute the data clear function.

Then, change the settings.

Turn off the power to the device

and turn it on after a while. If the

same error message appears again

on the LCD, contact your local

distributor to call for service.

Refer to "Setting the media".

page 2.16.

If this error cannot be resolved

even after setting it correctly,

contact the dealer.

Turn off the power to the device

and turn it on after a while. If the

same error message appears again

on the LCD, contact your local

distributor to call for service.

2x Data Cable for Mimaki JV3 JV22 Epson DX4 Print Head 21 pin 23 cm USA Seller

Seller assumes all responsibility for this listing.
New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is ... New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. See all condition definitionsopens in a new window or tab
Mimaki Printers with Epson (Dx4) printhead: JV3
8x 23 cm 21 pin data cable
Seller assumes all responsibility for this listing.
Item does not ship to Israel
Chino, California, United States
S.), Wallis and Futuna, Western Sahara, Western Samoa, Yemen, Zambia, Zimbabwe
Will usually ship within 1 business day of receiving cleared payment.

Sales Tax for an item #172327152246

Sales Tax for an item #172327152246

Seller collects sales tax for items shipped to the following states:
      
Signs101.com: Largest Forum for Signmaking Professionals
  • I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
Keep getting this error when trying to get a 8' banner printed for a customer... it seems to be happening at different times ( tried 3 times). Checked all the problems listed online and that dont seem to fix it. I checked the connection, the software( seems to working fine), any ideas?
After a quick search online it appears that an Error 23 for a JV3 is a communications error. Start with replacing the firewire cable, then I would suggest that the firewire card in the printer might be going bad, or possibly the one in your PC. If you need a good local Mimaki tech I will send you the info via PM.
Thanks for the input, I will try a new cable, I already checked to make sure it was connected good. Since it's intermittent I would say it's a card
Update

Well I got it going again, should have done this first when it was a communication error. Just restarted the printing computer everything worked fine.
yeah, could be the card. same issue here, but when away after replacement.
The I/O board was actually the only electrical component on that printer I've ever had to replace aside from ribbon cables.
  • This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.

You can watch a thematic video

Pioneer FH-X700BT Error 23 Fix
Signs101.com: Largest Forum for Signmaking Professionals
  • I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 .
You are using an out of date browser. It may not mikrowellen terror psychoterror this or other websites correctly.
You should upgrade or use an alternative browser.
Keep getting this error when trying to get a 8' banner printed jv3 error 23 a customer., jv3 error 23. it seems to be happening at different times ( tried 3 times), jv3 error 23. Checked all the problems listed online and that dont seem to fix it. I checked the connection, the software( seems to working fine), any ideas?
After a quick search online it appears that an Error 23 for a JV3 is a communications error. Start with replacing the firewire cable, then I would suggest that the firewire card in the printer might be going bad, or possibly the one in your PC. If you need a good local Mimaki tech I will send you the info via PM.
Thanks for the input, I will try a new cable, I already checked to make sure it was connected good. Since it's intermittent I would say it's a card
Update

Well I got it going again, should have done this first when it was a communication error. Just restarted the printing computer everything worked fine.
yeah, could be the card. same issue here, but when away after replacement.
The I/O board was actually the only electrical component on that printer I've ever had to replace aside from ribbon cables.
  • This site uses cookies to help personalise content, tailor your experience and to keep startservicectrldispatcher error = 1063 logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.

Mimaki JV3-160SP Error Codes and quick guides [Solved]

Fixing Mimaki JV3-160SP Error Codes list

– Compatible Printer model: Mimaki JV3-160SP
– Mimaki JV3-160SP Error Code description:

  • Code: 01
  • Display: ERROR01 MAIN Canon error 006 • The control ROM is in abnormal conditions.
  • Troubleshooting Guides: 1) Replace the main PCB with a new one.
  • Code: 02
  • Display: ERROR02 MAIN RAM
  • Description: • The control RAM is in abnormal conditions.
  • Troubleshooting Guides: 1) Drive_layout_information_ex a error the main PCB with a new one.
  • Code: 03
  • Display: ERROR03 POWER +5V POWER +35V
  • Description: • The +5V (+35V) voltage is in abnormal conditions.
  • Troubleshooting Guides: 1) Replace the power supply or the main PCB with a new one.
  • Code: 04
  • Display: ERROR04 FLASH ROM
  • Description: • The Flash memory is in abnormal conditions.
  • Troubleshooting Guides: 1) Replace the main PCB with a new one.
  • Code: 06
  • Display: ERROR06 D-RAM
  • Description: • An error has occurred in the D-RAM.
  • Troubleshooting Guides: 1) Replace the main PCB with a new one.
  • Code: 07
  • Display: ERROR07 TEMP jv3 error 23 • Abnormal temperature is detected.
  • Troubleshooting Guides: 1) Has ink in the camper run out? 2) Check the FPC cable connection. 3) Replace the Slider PCB with a new one. 4) Replace the head with a new one. 5) Replace the main PCB with a new one.

Mimaki JV3-160SP error code

  • Code: 08
  • Display: ERROR08 ENCODER
  • Description: • The Linear encoder is in abnormal conditions.
  • Troubleshooting Guides: 1) Replace the Linear encoder with a new one. 2) Replace the main PCB with a new one.
  • Code: 09
  • Display: ERROR09 HDC
  • Description: • Configuration of PDC/IOC has not been successfully carried out, jv3 error 23. •Configuration of HDC has not been successfully carried out.
  • Troubleshooting Guides: 1) Replace the main PCB with a new one.
  • Code: 10
  • Display: ERROR10 COMMAND
  • Description: •Command code other than MRL has been received.
  • Troubleshooting Guides: 1) Check the data received through HEX dump. 2) If error occurs at 1394 a. Check Time out of the transfer tool (RIP). b. Replace the I/F connection board with [E102154A] or later. c. Replace the 1394 board with a new one. d. Replace the main PCB with a new one. e. Supply power to the 1394 PCI board in the PC through the power cable.
  • Code: 11
  • Display: ERROR11 PARAMETER
  • Description: • Parameter that has not defined in MRL has been received.
  • Troubleshooting Guides: 1) Check the data received through HEX dump. 2) If error occurs at 1394 a. Check Time out of the transfer tool (RIP). b. Replace the I/F connection board with [E102154A] or later. c, jv3 error 23. Jv3 error 23 the 1394 board with a bios checksum error defaults loaded one. d. Replace the main PCB with a new one. e. Supply power to the 1394 PCI board in the PC through the power cable.
  • Code: 12
  • Display: ERROR12 Ment Command
  • Description: •A command error for manufacture of has occurred.
  • Troubleshooting Guides: 1) It is not used in the field
  • Code: 20
  • Display: ERROR20 I/F BOARD
  • Description: •A error occurred in communication between the main PCB and the interface board.
  • Troubleshooting Guides: 1) Replace the I/F PCB with a new one. 2) Replace the main PCB with a new one, jv3 error 23. 3) Replace the I/F connection board with a new one. 4) Supply power to the 1394 PCI board in the PC through the power cable.

– Mimaki JV3-160SP Error codes and solution steps to solve problems:

  • Code: 21
  • Display: ERROR21 I/F NONE
  • Description: • The I/F board could not be recognized.
  • Troubleshooting Guides: 1) Is the I/F board mounted correctly?
  • Code: 23
  • Display: ERROR23 HOST I/F
  • Description: •A time limit exceeded error occurred in communication between the host computer and the interface board.
  • Troubleshooting Guides: 1) Is the cable loose? 2) Has an error occurred on the host computer? 3) Is the application being used running normally?
  • Code: 24
  • Display: ERROR24 I/F INITIAL
  • Description: • The I/F board is in abnormal conditions.
  • Troubleshooting Guides: 1) Replace the I/F PCBwith a new one. 2) Replace the main PCB with a new one. 3) Replace the main PCB with a new one.
  • Code: 30
  • Display: ERROR30 OPERATION
  • Description: • Improper operation has been eth0 error while getting interface flags Guides: 1) Indicate the improper operation. 2) Replace a key board. 3) Replace a main PCB.
  • Code: 34
  • Display: ERROR34 DATA REMAIN
  • Description: • Operating condition is tried to be changed when data that has not yet been plotted remains.
  • Troubleshooting Guides: 1) This tells that any of the operating conditions cannot be changed if data that have not been plotted remains.
  • Code: 40
  • Display: ERROR40 MOTOR X
  • Description: • The X-axis motor has been overloaded.
  • Troubleshooting Guides: 1) Replace X axis motor. 2) Replace a main PCB.
  • Code: 41
  • Display: ERROR41 MOTOR Y
  • Description: • The Y-axis motor has been overloaded. • The brush of motor is in abnormal conditions.
  • Troubleshooting Guides: 1) Clean the main guide axis. 2) Replace Y axis motor. 3) Replace a main PCB.
  • Code: 42
  • Display: ERROR42 X CURRENT
  • Description: • Overcurrent error has arisen on the X-axis motor
  • Troubleshooting Guides: 1) Replace X axis motor. 2) Replace a main PCB.
  • Code: 43
  • Display: ERROR43 Y CURRENT
  • Description: • Overcurrent error has arisen on the Y-axis motor
  • Troubleshooting Guides: 1) Replace Y jv3 error 23 motor. 2) Replace a main PCB.
  • Code: 46
  • Display: ERROR46 WIPER
  • Description: • The wiper-control is in abnormal conditions.
  • Troubleshooting Guides: 1) Turn on the power. jv3 error 23 Replace a wiper assy. 3) Replace IO PCB. 4) Replace a wiper sensor. 5) Replace a wiper motor.
  • Code: 50
  • Display: ERROR50 MEDIA SENSE
  • Description: • Media detection has not been successfully carried out.
  • Troubleshooting Guides: 1) Make sure that there is no gap between platen F (aluminum) and the edge of the P cover F rubber. If there is a gap, stick the rubber appressed against the platen. The gap may be detected in mistake. 2) Make sure that platen cover F is fixed securely using the platen cover F mounting screws (attached on auxiliary side plates R and L to prevent the cover from protruding). 3) Check if the media right edge is set at a position 15mm or more from the rightmost edge of the rightmost feed roller:R1 toward the station side or not. 4) Cleaning or replace a paper width sensor. 5) Replace a HDC FPC cable. 6) Replace a slider PCB, jv3 error 23. 7) Replace a main PCB.
  • Code: 51
  • Display: ERROR51 Y ORIGIN
  • Description: • Y-axis origin detection has not been successfully carried out.
  • Troubleshooting Guides: 1) Replace a Y axis motor. 2) Replace a Y origin sensor, jv3 error 23. 3) Replace a IO PCB, jv3 error 23. 4) Replace a main PCB.

Waste Ink Pad Counter Utility Functions:

– Cleaning printhead.
– Ink charge.
– Fix Epson red lights blinking Error

Epson red lights blinking 2

– Fix Epson Service Required Error: A printer’s ink pad at the end of its service life Please contact Epson Support.
Epson red lights blinking 2

– Check the current value of waste ink counters and ink level counters.
– Clear Waste Ink Counters.
– Read and write serial number.
– Read and write USB ID.
– Read and write HEAD ID.
– Make EEPROM dump, backup.
– Paper feed test.
– Nozzle check.
– Color check pattern.
– Initialize (disable) PF deterioration offset.
– Retrieve device information

Contact us to get support with Mimaki JV3-160SP Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/

Filed Under: error code, MimakiTagged With: fix Mimaki JV3-160SP, Mimaki JV3-160SP Error, Mimaki JV3-160SP repair service, Mimaki JV3-160SP troubleshooting

Error message

ERROR 23

HOST Jv3 error 23 / F

ERROR 24

I / F INITIAL

ERROR 30

OPERATION

ERROR 34

DATA REMAIN

ERROR 40

MOTOR X

ERROR 41

MOTOR Y

ERROR 42

X CURRENT

ERROR 43

Y CURRENT

ERROR 46

WIPER

ERROR 50

MEDIA SENSE

ERROR 51

Y ORIGIN

ERROR 57

HEAD HIGHT SENS.

Cause

HOST I/F Timeout error has

arisen during communication

between the host computer and

interface board.

Initial operation failure of the I/F

board and control board.

An error occurs on the interface

between the I/F board and the

control board.

Settings for functions have been

tried to be changed though there

remains received data that has not

yet been printed.

The Xmotor has been overload.

The Ymotor has been overload.

Overcurrent error on the Xmotor

has been detected.

Overcurrent error on the Ymotor

has been detected.

The wiper position is not

correct.

Paper could not be detected.

The media set position or media

itself is not correct.

Origin could not be detected.

Head height could not be

detected.

- 6.9 -

Corrective measure

Check to be sure that the cable is

securely connected to the host

computer and interface board.

Also, check to ascertain that no

error has arisen on the host

computer side.

Turn off the power to the device

and turn it on after a while, jv3 error 23. If the

same error message appears again

on the LCD, contact your local

distributor to call for service.

Perform a proper operation.

Print all pieces of received data or

execute the data clear function.

Then, change the settings.

Turn off the power to the device

and turn it on after a while. If the

same error message appears again

on the LCD, contact your local

distributor to call for service.

Refer to "Setting the media".

page 2.16.

If this error cannot be resolved

even after setting it correctly,

contact the dealer.

Turn off the power to the device

and turn it on after a while. If the

same error message appears again

on the LCD, contact your local

distributor to call for service.

We have noticed an unusual activity from your IP 62.89.30.2 and blocked access to this website.

Please confirm that you are not a robot.

2x Data Cable for Mimaki JV3 JV22 Epson DX4 Print Head 21 pin 23 cm USA Seller

Seller assumes all responsibility for this listing.
New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is . New: Jv3 error 23 brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. See all condition definitionsopens in a new window or tab
Mimaki Printers with Epson (Dx4) printhead: JV3
8x 23 cm 21 pin data cable
Seller assumes all responsibility for this listing.
Item does not ship to Israel
Chino, California, United States
S.), Wallis and Futuna, Western Sahara, Western Samoa, Yemen, Zambia, jv3 error 23, Zimbabwe
Will usually ship within 1 business day of receiving cleared payment.

Sales Tax for an item #172327152246

Sales Tax for an item #172327152246

Seller collects sales tax for items shipped to the following states:
      

Error message

ERROR 23

HOST I / F

ERROR 24

I / F INITIAL

ERROR 30

OPERATION

ERROR 34

DATA REMAIN

ERROR 40

MOTOR X

ERROR 41

MOTOR Y

ERROR 42

X CURRENT

ERROR 43

Y CURRENT

ERROR 46

WIPER

ERROR 50

MEDIA SENSE

ERROR 51

Y ORIGIN

ERROR 57

HEAD HIGHT SENS.

Cause

HOST I/F Timeout error has

arisen during communication

between the host computer

and interface board.

Initial operation failure of the I/

F board and control jv3 error 23 error occurs on the inter-

face between the I/F board

and the control board.

Settings for functions have been

tried to be jv3 error 23 though there

remains received data that has

not yet been printed.

The Xmotor has been overload.

The Ymotor has been overload.

Overcurrent error on the

Xmotor has been detected.

Overcurrent error on the

Ymotor has been detected.

The wiper position is not

correct.

Paper could not be detected.

The media set position or

media itself is not correct.

Origin could not be detected.

Head height could not be

detected.

- 6.10 -

Corrective measure

Check to be sure that the cable

is securely connected to the

host computer and interface

board. Also, check to ascertain

that no error has arisen on the

host computer side.

Turn off the power to the device

and turn it on after a while. If the

same error message appears

again on the LCD, contact your

local distributor jv3 error 23 call for service.

Perform a proper operation.

Print all pieces of received

data or execute the data clear

function. Then, jv3 error 23, change the

settings.

Turn off the power to the

device and turn it on after a

while. If the same error

message appears again on the

LCD, contact your local dis-

tributor to call for service.

Refer to "Setting the media".

page 2.8.

If this error cannot be resolved

even after setting it correctly,

contact the dealer.

Turn off the power to the

device and turn it on after a

while. If the same error

message appears again jv3 error 23 the

LCD, contact your local dis-

tributor to call for service.

jv3 error 23

0 Comments

Leave a Comment