Feed motor error code 0008 0008

feed motor error code 0008 0008

Troubleshooting Guides: Code: 0008; Description: Feed Motor Overcurrent Error 2 (A little load is put on the motor for a long time.) Causes. Description: Feed Motor Deviation Error (The order from the CPU does not match the feedback of the Feed Motor.) Roland RS640 VersaArt Common Errors. The most. Code: 0008; Description: SCAN MOTOR ERROR; Causes: Feed Motor Overcurrent Error 2 (A little load is put on the motor movement for a long.

Feed motor error code 0008 0008 - simply matchless

Designjet Error Codes

T7300001-0082Real Time Clock (RTC) Battery ran down.go to the Support Menu by pressing the Power key continuously for 15 seconds, Go to the Diagnostics Menu check RTC battery status, replace the RTC battery by replacing the Main PCAT7300004-0001Printer Bundle Board communication failure or malfunctionTurn off/on. Check Cables in bundle pCA, Repalce Bundle PCA, Replace Bundle FFC cable, Repalce the Main PCAT7300008-0001Onsite troubleshooting and solution (service engineer)No communication between the Front Panel and the Main PCA, e beeps. Call service engineer.T7300021-0132Weak primer motor or underpowered motorTurn off/on. Check cable to prime pump & PCA, Replace cables, replace Pump motor, replace the Print bundle PCA.T7300021-0161Priming motor or electrical failureTurn off/on. Check cables, Replace Priming motor, Replace the Print bundle PCA,T7300021-0180Air Leak in Priming SystemTurn off/on. Remove cover and check Prime Pump air circuit, inspect Fluidic connections. Repalce Fluidic pump, replace pump motorT7300024-0000The ink does not flow to the PHA during the PHA startup processReseat the PHA and ensure the ink tube connections are correct, install PHA replacement kit, replace RIDS (Ink Tubes)T7300024-1000Out of ink ,faulty or missing cartridge during the PHA startupCheck ink cartridges are seated, reinsert. Change ink to new cartridge.T7300024-1100Out of ink detected in altered suppliestry agin with New unused HP supplies.T7300026-0061ISS motor stall or bad encoder discRestart, run service diagnostic test to verify ISS, replace ISS, run Service diagnostics to test and verify ISS and sensorsT7300026-0100ISS Optotrip failureOtherTurn Off/on. Run ISS diagnostic test, insure ISS cables are OK, ensure no ink spots or debis on media or opto sensors. Replace ISST7300026-0200ISS Bongo MalfunctionCheck ink supplies. Ensure they are genuine HP ink supplies.T7300026-XXXXSilent S.E. for troubleshootingcall HP techT7300027-00XXPHA problem, Carriage PCA, Trailing Cable, Main PCARemove clean and reseat PHA kit, check ink tubes latch, if under warranty arrange for PHA replacementT7300041-0017Unable to move Paper Servo or no feedback received.Turn off/on. Go to support menu press Power key 15 sec. run paper servo diagnostic test, replace paper motor, replace feed encoder sensor PCA, repalce Paper Motor, Replace Main PCAT7300042-0117Unable to move Carriage Servo or no feedback received.Turn off/on. Check carriage motor belt, replace carriage belt, replace carriage motorT7300043-0017Unable to move Pick Servo or no feedback receivedRemove covers and chec that cables to Printer Bundle Board, pick motor . Repalce Cable, Repalce pick motorT7300045-0017Unable to move Rewind Servo or no feedback received.Turn off/on. Remove spindle, check gear and cap position, look for damage, replace spindle, check cable to Main PCA, repalce left roll support, replace main PCAT7300051-0101Top (SFP) or Front (MFP) Cover sensor failure, Main PCA failureTurn off/on. Run top cover sonsor diagnostic, replace the top cover sensor PCA, replace cable, replace Main PCAT7300051-0201PHA door sensor failureTurn off/on. Run top cover sonsor diagnostic, replace door sensor PCA, replace cable, replace Main PCAT7300051-0301Ink Cartridge door sensor failureTurn off/on. Check cable to door, replace ink cartidge door sensor, replace main PCAT7300053-0201Output Tray sensor failureTurn off/on. Run Output Tray Sensor diagnostic, Check output try sensor and replace if needed, replace output tray sensor assembly, replace Main PCAT7300059-0190Conflict found between NVM main and backupThe error appears if during a service operation, the Main PCA or the NVM backup PCA are replaced by a reused part (not a new spare part).T7300059-0191Default data found in both NVM main and backupThe error appears if during a service operation, the Main PCA and the NVM backup PCA are replaced at the same time, restart printer between replacing parts.T7300059-0289NVM backup is missing or does not work correctlyEnsure NVM backup cable is properly connected, replace the NVM backupT7300085-0101Feed index encoder sensor does not work properlyTurn off/on. Check all cables to the Main PCA, replace cables, repalce feed index encoder sensor PCA, replace Encoder DiskT7300085-0201Feed encoder sensor does not work properlyTurn off/on. Check cables connected to Main PCA,replace cables, replace feed encoder sensor PCA, replace encoder diskT7300087-0001Encoder Strip FailureTurn off/0n. Check the Encoder Strip, clean or replace. Replace encoder strip sensor.T7300153-0302Multi-Sheet Tray presence not detectedEnsure that the Multi-Sheet Tray is properly placed and the latch is closed, check cable connection to the MPCAT7300824-XXXXSilent ErrorIDS startup problem: Silent System Errors not shown in the Front Panel. Refer to Ink supplies troubleshooting for more informationT7300942-0188Carriage homing problemReboot system, clean encoder strip, Check encoder strip, scan axis and service station parts, repalce parts if needed.T7300955-0050Line sensor failureOtherTurn off/on, run the Line Sensor diagnostic , replace damaged cable, replace line sensor, replace carriage assembly, replace belt, replace Main PCA

Error code: 0007 - unable to locate spool

  • The Mini is unable to read the sensor chip inside of the spool. Using a philips screwdriver, open the white plastic spool and check that the sensor is seated in the the correct position. The sensor chip tracks the amount of filament you have used, and helps to calculate if you have enough to complete the print. When you purchase new filament supplied by XYZprinting, a sensor chip will also be included in the packaging. Without this sensor chip loaded the Mini will not be able to use the filament.

error-0007-02

Error code: 0008 - unable to locate spool

  • The Mini is unable to read the sensor chip inside of the spool. Using a philips screwdriver, open the white plastic spool and check that the sensor is seated in the the correct position. The sensor chip tracks the amount of filament you have used, and helps to calculate if you have enough to complete the print. When you purchase new filament supplied by XYZprinting, a sensor chip will also be included in the packaging. Without this sensor chip loaded the Mini will not be able to use the filament.

error-0007-02

Error code: 0011 - problem with heating

  • There was a problem with the extruder heating. Turn off the Mini and check to see if the extruder connector is securely connected. Restart you printer and retry. If you continue to get the same error, contact the XYZprinting service center for support.

Error code: 0014 - problem with heating

  • There was a problem with the extruder heating. Turn off the Mini and check to see if the extruder connector is securly connected. Restart you printer and retry. If you continue to get the same error, contact the XYZprinting service center for support.

Error code: 0016 - spool not properly installed

  • The Mini is unable to read the sensor chip inside of the spool. Using a philips screwdriver, open the white plastic spool and check that the sensor is seated in the the correct position. The sensor chip tracks the amount of filament you have used, and helps to calculate if you have enough to complete the print. When you purchase new filament supplied by XYZprinting, a sensor chip will also be included in the packaging. Without this sensor chip loaded the Mini will not be able to use the filament.

error-0007-02

Error code: 0028 - Spool not found

    • Spool may not be installed properly. To reinstall the spool, press Unload Filament then Load Filament in the printer dashboard. If you still get the same error, the Mini might be unable to read the sensor chip inside of the spool. Using a philips screwdriver, open the white plastic spool and check that the sensor is seated in the the correct position. The sensor chip tracks the amount of filament you have used, and helps to calculate if you have enough to complete the print. When you purchase new filament supplied by XYZprinting, a sensor chip will also be included in the packaging. Without this sensor chip loaded the Mini will not be able to use the filament.

error-0007-02

Error code: 0029 - no filament left in spool

    • No filament left in spool. Replace spool and sensor chip before printing. The sensor chip tracks the amount of filament you have used, and helps to calculate if you have enough to complete the print. When you purchase new filament supplied by XYZprinting, a sensor chip will also be included in the packaging. Without this sensor chip loaded the Mini will not be able to use the filament. When you replace the filament be sure to open the white plastic spool with a philliips screw driver and check that the sensor is seated in the the correct position.

error-0007-02

Error code: 0030 - problem with X-axis motor

  • Check that the X-axis motor is connected, then check that the X-axis sensor is in the right position and the connector is plugged in.

Error code: 0031 - problem with Y-axis motor

  • Check that the Y-axis motor is connected, then check that the Y-axis sensor is in the right position and the connector is plugged in.

Error code: 0032 - problem with Z-axis motor

  • Check that the Z-axis motor is connected, then check that the Z-axis sensor is in the right position and the connector is plugged in.

Error code: 0050 - memory error

  • Restart the printer, if the error persists, contact the service center for support.

Error code: 0054 - incompatible extruder module

  • Turn off printer, reinstall compatible extruder module, then restart your printer.If error persists, contact service center.

Unsupported file type

  • XYZware can only print .STL, .3W, and 3WF files. Try re-exporting the file as one of the these types and re-importing it again.

Error code: 020B - cannot detect SD card

  • Open up the back of your machine and check that the SD card is connected.

Error code: 020C - cannot detect SD card

  • Open up the back of your machine and check that the SD card is connected.

How to start or stop a print?

  • To start a print, click the print icon on the XYZware main screen, or view this first-time printing video.
  • The da Vinci can be stopped via PC or directly on the machine using theLED button.To stop the machine via PC, open XYZware, click on the Printer monitor icon in the bottom right-hand side of the screen and in the Printer Info window click on the stop icon.

Filament jammed / not coming out smoothly.

  • Cancel your current print, press the LED button on the da Vinci Mini and wait for the print bed to move to the front. The LED button should change from red to pulsing orange.
  • Remove your failed print and press the LED button one more time to return it to green status
  • Close and restart XYZware
  • Open the Printer monitor and click Extruder > Clean nozzle
  • Follow the onscreen instructions to clean your extruder nozzle
  • Nozzle cleaning video

If the filament spool can’t spin freely

  • Check that it is not coiled around the feed module.Filament must be loaded in a certain direction without any tangles, please see the picture below.

Untitled-3-01

Part doesn’t stick to print bed.

  • The distance between the extruder nozzle and the printing bed may not be close enough, attach bed tape and calibrate the da Vinci Mini

If you are still having problems try manually adjusting the Z offset

  • Open XYZware then go printing monitor
  • In the printing monitor go to SetUp → jog mode → home axis → Finished. The extruder will go back to its original position.
  • Move the extruder module to the middle of the print bed using the onscreen buttons.
  • Check if the tape has been scratched or not; if you can fit two A4 pieces of paper between the extruder nozzle and print bed comfortably, press Home axes again to move the extruder back to the initial axis, then proceed to the step below.
  • Go Setting → Z offset to set the Z offset; manually move the nozzle to the middle, the ideal distance between extruder nozzle and print bed should be a snug fit of two standard A4 sheets of paper. Use the Z-offset figures to decrease the gap by 0.1mm increments and click Accept. 

Filament not coming out of the extruder, bed tape is being scratched and shifting position.

  • The distance between the extruder nozzle and the printing bed may be too close, attach bed tape and calibrate the da Vinci Mini.

If you are still having problems try manually adjusting the Z offset

  • Open XYZware then go printing monitor
  • In the printing monitor go to SetUp → jog mode → home axis → Finished. The extruder will go back to its original position.
  • Move the extruder module to the middle of the print bed using the onscreen buttons.
  • Check if the tape has been scratched or not; if the distance between extruder nozzle and the print bed is too close, press Home axes again to move the extruder back to the initial position, then proceed to the step below.
  • Go Setting → Z offset to set the Z offset; manually move the nozzle to the middle, the ideal distance between extruder nozzle and print bed should be two standard A4 sheets of paper. If you cannot fit two pieces of paper between the extruder nozzle and print bed, use the Z-offset figures to increase the gap by 0.1mm increments and click accept.

The printer is making thudding noise when printing

  • Check to see if the noise is originating from the feed module
  • When the feed module makes a noise it is generally because the filament is stuck, and the motor is slipping when trying to extrude the filament
  • Make sure the filament spool can spin freely
  • The extruder module may be jammed, follow this tutorial on how to clean the extruder nozzle 
  • The distance between the print bed and extruder module may be too close – follow the instructions from the previous problem
  • Feed module teeth may need cleaning. Drive gear cleaning video. 

Printer stops mid print

  • Check that your printer power supply is plugged in and that there hasn’t been a power shortage recently
  • Make sure the print file has transferred from your computer to the da Vinci Mini and that the print was started before removing the USB cable. The larger the 3D file the longer the transfer will take.
  • Turn the printer back on immediately and unload the filament to ensure the extruder nozzle hasn’t jammed

The guide tube has come loose inside the feeding tube grip and pops out during printing

  • Overtime the guide tube wears where the feed tube grip connects to it. When this happens we recommend following this trim guide tube tutorial.
  • If the problem persists it may be that the teeth on the feeding tube grip are worn and do not hold the guide grip in place. If this is the case, try replacing the tube grip with the replacement supplied in the packaging.

XYZware displays "Printer Error" after I have clicked print

After a print or if a print fails, you need to return the LED button to its green state

  • If the LED button is red or orange, push it once to make it return to a green state. The printer is now ready to print.

XYZware will not connect to the da Vinci Mini

Ensure the da Vinci Mini’s USB cable is connected to the printer and your computer:

  • Turn on the da Vinci Mini
  • Restart XYZware
  • Click on the Printer monitor and wait for XYZware to automatically detect the da Vinci Mini

If you are still having issues connecting to the da Vinci Mini, try manually connecting:

  • In XYZware click Settings > Printer > Printer type > da Vinci Mini W or da Vinci miniMaker

The print monitor is displaying error code: 0028

  • Check that the filament spool has a white filament spool ring attached to it
  • Put the filament spool on the spool holder to the left-hand side of the da Vinci Mini
  • If the above suggestions do not work, open up the filament spool ring using a phillip screwdriver and check that there is a sensor chip inside.

Image 9

When you purchase new XYZprinting filament, it comes with a NFC sensor chip that you need to load into the filament spool ring before use. This sensor chip tracks the type of filament, how much you have used, and is able to let you know if you have enough to complete the print. Without the sensor chip, the printer will be unable to work.
The da Vinci Mini’s extruder module has been designed to extrude only XYZprinting PLA filament; because 3rd party filaments often jam inside the extruder,  only XYZprinting filament will work with the da Vinci Mini.

Purchase new filament

Not enough filament alert shown, how do I go back to the monitor page?

The alert is displayed when you have 30% filament remaining, click the button to go back to the main screen.

 

Filament questions

Does Mini accept ABS filament?

  • Mini is designed for the PLA filament – the use of other filaments may cause the extruder nozzle to jam and result in printer failure.

What is PLA?

  • Polylactic acid or polylactide (PLA, Poly) is a biodegradable thermoplastic aliphatic polyester derived from renewable resources, such as corn starch, tapioca roots, chips or starch, or sugarcane.

Can the filament of all da Vinci series be used with Mini?

  • No, the Mini uses NFC filament designed for only the da Vinci Mini and Junior. This filament can be purchased here.
  • When you purchase new XYZprinting filament, it comes with a NFC sensor chip that you need to load into the filament spool ring before use.This sensor chip tracks the type of filament, how much you have used, and will let you know if you have enough to complete the print. Without the sensor chip the printer will not be able to work.

 

Hardware questions

What is the size of the Mini's printable area?

  • The Mini can print up 15 x 15 x 15 cm.

How many 3D printers can be connected to one PC?

  • Multiple printers can be connected to one PC, however, XYZware can only send one job at a time.

 

Other questions

How long is the warranty period?

  • The warranty for the printer is 1 year, the extruder module is under warranty for 90 days.

 

We have noticed an unusual activity from your IP 62.89.30.2 and blocked access to this website.

Please confirm that you are not a robot.

Solved Roland VS540 VersaCamm Error Codes and description

Solved Roland VS540 VersaCamm Error Codes

– Printer model: Roland VS540 VersaCamm
– Error codes on Roland VS540 VersaCamm model and its description:

Roland VS540 VersaCamm error code

– Roland VS540 VersaCamm printer Error Codes and quick guide to troubleshooting:

  • Code: 0001
  • Description: SCAN MOTOR ERROR
  • Causes: Feed Motor Deviation Error (The order from the CPU does not match the feedback of the Feed Motor.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0002
  • Description: Disorder of communication with Sub CPU This occurs when the Sub CPU is not detected after turning on the machine.
  • Causes: Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board.
  • Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check the other cable connections of Servo Board. Servo Board replacement Main Board replacement Flexible cable replacement
  • Code: 0004
  • Description: Sub CPU SRAM error
  • Causes: SRAM is broken.
  • Troubleshooting Guides: Servo Board replacement
  • Code: 0004
  • Description: SCAN MOTOR ERROR
  • Causes: Feed Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0005
  • Description: An error occurs during downloading a program for sub CPU.
  • Causes: Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board. A noise on a signal
  • Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check the other cable connections of Servo Board. Servo Board replacement Main Board replacement Flexible cable replacement
  • Code: 0005
  • Description: SCAN MOTOR ERROR
  • Causes: Feed Motor Deviation Error (The order from the CPU does not match the feedback of the Feed Motor.) Feed Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0006
  • Description: An error occurs when trying to connect with sub CPU.
  • Causes: A noise on a signal while sending a command Sub CPU was reset to default. Tried to communicate when Sub CPU was reset to default.
  • Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check the other cable connections of Servo Board. Servo Board replacement Main Board replacement Flexible cable replacement
  • Code: 0007
  • Description: An error occurs while sending a command.
  • Causes: Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board. A noise on a signal while sending a command Sub CPU was reset while sending a command.
  • Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check the other cable connections of Servo Board. Servo Board replacement Main Board replacement Flexible cable replacement
  • Code: 0008
  • Description: There is a problem with synchronizing serial communication to Sub CPU.
  • Causes: Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board. A noise on a signal
  • Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check the other cable connections of Servo Board. Servo Board replacement Main Board replacement Flexible cable replacement
  • Code: 0008
  • Description: SCAN MOTOR ERROR
  • Causes: Feed Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0009
  • Description: SCAN MOTOR ERROR
  • Causes: Feed Motor Deviation Error (The order from the CPU does not match the feedback of the Feed Motor.) Feed Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 000C
  • Description: SCAN MOTOR ERROR
  • Causes: Feed Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.) Feed Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0010
  • Description: SCAN MOTOR ERROR
  • Causes: Scan Motor Deviation Error (The order from the CPU does not match the feedback of the Scan Motor.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0010
  • Description: Network I/F Initialize has not been completed.
  • Causes: Network I/F does not work correctly. Firmware for Network I/F is not installed.
  • Troubleshooting Guides: Check the fi rmware is installed into Network I/F. Main Board replacement
  • Code: 0040
  • Description: SCAN MOTOR ERROR
  • Causes: Scan Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0050
  • Description: SCAN MOTOR ERROR
  • Causes: Scan Motor Deviation Error (The order from the CPU does not match the feedback of the Scan Motor.) Scan Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0080
  • Description: SCAN MOTOR ERROR
  • Causes: Scan Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0090
  • Description: SCAN MOTOR ERROR
  • Causes: Scan Motor Deviation Error (The order from the CPU does not match the feedback of the Scan Motor.) Scan Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 00C0
  • Description: SCAN MOTOR ERROR
  • Causes: Scan Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.) Scan Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0101
  • Description: Limit Position Initialize in the Service Mode has not been done.
  • Causes: Limit Position Initialize has not been done. Limit Position Initialize is ended before it is completed.
  • Troubleshooting Guides: Complete Limit Position Initialize correctly.
  • Code: 0102
  • Description: Head Lock Sensor is ON when it should be OFF, or vice versa.
  • Causes: Head Lock Sensor does not work correctly or is broken. Head Carriage is not located at the correct position.
  • Troubleshooting Guides: Head Lock Sensor replacement Check the mechanical backlash or loose with the scan axis related parts.
  • Code: 0103
  • Description: Limit Sensor is ON when it should be OFF, or vice versa.
  • Causes: Limit Sensor does not work correctly or is broken. Tool Carriage is not located at the correct position.
  • Troubleshooting Guides: Limit Sensor replacement Check the mechanical backlash or loose with the scan axis related parts. Revised 1
  • Code: 0105
  • Description: Tool Carriage Connection Error
  • Causes: Fault of Tool Carriage Connection Loose of Connection Part Fault of the Limit Position Initialize value Limit Sensor does not work correctly or is broken.
  • Troubleshooting Guides: Check the mechanical Backlash or loose with the Tool Carriage part. Connection Part Replacement Limit Position Initialize
  • Code: 0106
  • Description: Machine fails to disconnect the Tool Carriage from the Head Carriage.
  • Causes: Fault of Tool Carriage Connection Loose of Connection Part Fault of the Limit Position Initialize value Limit Sensor does not work correctly or is broken.
  • Troubleshooting Guides: Check the mechanical Backlash or loose with the Tool Carriage part. Connection Part Replacement Limit Position Initialize
  • Code: 0107
  • Description: Linear Encoder Setup has not been done.
  • Causes: Linear Encoder Setup has not been done. Linear Encoder Setup is ended before it is completed.
  • Troubleshooting Guides: Carry out Linear Encoder Setup in service menu.
  • Code: 0109
  • Description: Wiper unit does not work correctly.
  • Causes: Wiper Unit hits the Tool Carriage Wiper Motor error Defect of Wiper Unit Defect of Wiper Sensor Cut-line or short-circuit of cable and Flexible cable
  • Troubleshooting Guides: Move the Head Carriages on the bed not to hit the Wiper Unit. Wiper Motor Replacement Wiper Unit Replacement Wiper Sensor Replacement Cable and Flexible Cable Replacement
  • Code: 0110
  • Description: Input value from Linear Encoder is not changed by the Linear Encoder origin setup. When Motor stops during printing, expected movement is not completed on some head.
  • Causes: Read error of Linear Encoder Read error of Encoder on Scan Motor side Belt is not fi xed to Head Carriage fi rmly.
  • Troubleshooting Guides: Confi rm whether Encoder Scale is in the slit of Encoder Module in a whole width of the machine. Check cable connection between Linear Encoder Board and Main Board. Confi rm connection between Belt and Tool Carriage. Linear Encoder replacement Scan Motor replacement Servo Board replacement Main Board replacement
  • Code: 0111
  • Description: This error occurs when the machine performs the Auto Crop Mark Detection before performing Crop- Cut Adjustment.
  • Causes: Crop-Cut Adjustment in the Service menu has not been performed.
  • Troubleshooting Guides: Carry out Crop-Cut Adjustment in service menu.
  • Code: 0112
  • Description: Communication error with Cartridge IC driver
  • Causes: Cartridge IC driver is broken. Cartridge IC driver cable has short circuited or cut-line.
  • Troubleshooting Guides: Ink cartridge IC sensor replacement
  • Code: 0130
  • Description: There is a problem with Thermistor for Print Heater.
  • Causes: Thermistor cable has short circuited or cutline. Thermistor has a problem.
  • Troubleshooting Guides: Check cable connection around Thermistor. Thermistor replacement
  • Code: 0135
  • Description: Print Heater temperature has reached 60°C and above.
  • Causes: Print Heater Cable connection has a problem. Thermostat has a problem. Thermistor has a problem.
  • Troubleshooting Guides: Check Print Heater. Check Thermostat. Check Thermistor.
  • Code: 0140
  • Description: There is a problem with Thermistor for dryer.
  • Causes: Thermistor cable has short circuited or cutline. Thermistor has a problem.
  • Troubleshooting Guides: Check Cable connection around Thermistor. Thermistor replacement
  • Code: 0145
  • Description: Dryer temperature has reached 80°C and above.
  • Causes: Dryer cable connection has a problem. Thermostat has a problem. Thermistor has a problem.
  • Troubleshooting Guides: Check Dryer. Check Thermostat. Check Thermistor.
  • Code: 0250
  • Description: There is a problem with Head device.
  • Causes: Head is broken.
  • Troubleshooting Guides: Head replacement

About Canon Servie Tool V5610

Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.

Canon Service Tool V5610

– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.

Canon Service Tool V5610 Functions

– Fix Canon printer 7 times/ 8 times red light blinking:

Fix 7 times/ 8 times red light blinking

– Fix Canon printer error code: 5B00, 5B01, 1700, 1701

Fix error code: 5B00, 5B01, 1700, 1701

Enter Service Mode on Canon Printer

1. Turn off a printer
2. Press and hold the Resume/Cancel/Stop button
3. Press and hold the ON button (do not release both buttons)
4. Release the Resume/Cancel/Stop button (do not release the ON button)
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.

For more information about Canon Serice Tool V5610

Contact us to get support with Roland VS540 VersaCamm Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/

Filed Under: error code, RolandTagged With: Canon Service Tool, fix Roland VS540 VersaCamm, Roland VS540 VersaCamm Error, Roland VS540 VersaCamm repair service, Roland VS540 VersaCamm troubleshooting

decodeURIComponent decodeURIComponent

6-10 MOTOR ERROR

NO

CHECKING POINT

1

Media Jam

Broken / life of the

2

Motor

Power Supply

3

voltage for Motor is

not supplied

4

Broken Motor Driver

There is a dirt in

5

teeth of Drive Gear.

Weight of Media

6

exceeds usable

Media.

MOTOR ERROR

< ERROR DESCRIPTION

SCAN MOTOR ERROR

CODE :

< ERROR LIST >

Bit

No.

Feed Motor Deviation Error

0001

Feed Motor Overcurrent Error 1

(Big load is put on the motor movement

0004

Feed Motor Overcurrent Error 2

(A little load is put on the motor

0008

movement for a long time.)

0001 and 0004 occurred at the same

0005

Revised 4

0001 and 0008 occurred at the same

0009

0010

Scan Motor Deviation Error

Scan Motor Overcurrent Error 1

0040

(Big load is put on the motor movement

Scan Motor Overcurrent Error 2

(A little load is put on the motor

0080

movement for a long time.)

0010 and 0040 occurred at the same

0050

Revised 4

0010 and 0080 occurred at the same

0090

ACTION

Remove cause of

Media Jam.

Motor

Replacement

Replace Switching

Power Supply

Mainboard

Replacement

Clean Drive Gear.

Use usable Media.

0000

0000

Record for LAST ERROR

CURRENT ERROR

MEANING

instantaneously.)

time.

time.

instantaneously.)

time.

time.

REFERENCE

When the edges of the media curls or the media

absorbs the Ink and becomes to be irregular

surface of the media, the Head Carriage catches

on the media during printing and results in the

Motor Error.

[3-5 Carriage

When the Motor is broken or reaches its life, the

Motor

Motor cannot obey the order from the CPU and it

Replacement]

results in the Motor Error.

[3-13 SW Power

When the Power Supply voltage for the Motor is

Supply

not supplied, the Motor cannot move and it results

Replacement]

in the Motor Error.

When the Servo Board is broken, the Power

Supply voltage for the Motor is not supplied and

the Motor cannot move. It results in the Motor

Error.

When there is a dirt in the teeth of the Drive Gear

and it cannot rotate, the Motor Error occurs.

When the weight of Media is too heavy, the Motor

Error occurs due to the too much load for feeding

Media.

Display the axis which the Error happens.

< User side >

1. Media Jam

2. Pull or Move the Carriage by hands.

3. Carriage runs into a thing/hands.

4. Media is stuck because the media end is not separated from the

paper tube.

5. Heavy media is used.

< Mechanical Side >

1. There is a bad contact/cut-line in the cable.

2. Screw fixing the tool carriage to wire is shifted.

3. Motor is broken./Life

4. Head/Servo Board is broken.

6-8

OUTLINE

CAUSE

Feed motor error code 0008 0008 - remarkable

Solved Roland VS540 VersaCamm Error Codes and description

Solved Roland VS540 VersaCamm Error Codes

– Printer model: Roland VS540 VersaCamm
– Error codes on Roland VS540 VersaCamm model and its description:

Roland VS540 VersaCamm error code

– Roland VS540 VersaCamm printer Error Codes and quick guide to troubleshooting:

  • Code: 0001
  • Description: SCAN MOTOR ERROR
  • Causes: Feed Motor Deviation Error (The order from the CPU does not match the feedback of the Feed Motor.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0002
  • Description: Disorder of communication with Sub CPU This occurs when the Sub CPU is not detected after turning on the machine.
  • Causes: Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board.
  • Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check the other cable connections of Servo Board. Servo Board replacement Main Board replacement Flexible cable replacement
  • Code: 0004
  • Description: Sub CPU SRAM error
  • Causes: SRAM is broken.
  • Troubleshooting Guides: Servo Board replacement
  • Code: 0004
  • Description: SCAN MOTOR ERROR
  • Causes: Feed Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0005
  • Description: An error occurs during downloading a program for sub CPU.
  • Causes: Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board. A noise on a signal
  • Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check the other cable connections of Servo Board. Servo Board replacement Main Board replacement Flexible cable replacement
  • Code: 0005
  • Description: SCAN MOTOR ERROR
  • Causes: Feed Motor Deviation Error (The order from the CPU does not match the feedback of the Feed Motor.) Feed Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0006
  • Description: An error occurs when trying to connect with sub CPU.
  • Causes: A noise on a signal while sending a command Sub CPU was reset to default. Tried to communicate when Sub CPU was reset to default.
  • Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check the other cable connections of Servo Board. Servo Board replacement Main Board replacement Flexible cable replacement
  • Code: 0007
  • Description: An error occurs while sending a command.
  • Causes: Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board. A noise on a signal while sending a command Sub CPU was reset while sending a command.
  • Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check the other cable connections of Servo Board. Servo Board replacement Main Board replacement Flexible cable replacement
  • Code: 0008
  • Description: There is a problem with synchronizing serial communication to Sub CPU.
  • Causes: Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board. A noise on a signal
  • Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check the other cable connections of Servo Board. Servo Board replacement Main Board replacement Flexible cable replacement
  • Code: 0008
  • Description: SCAN MOTOR ERROR
  • Causes: Feed Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0009
  • Description: SCAN MOTOR ERROR
  • Causes: Feed Motor Deviation Error (The order from the CPU does not match the feedback of the Feed Motor.) Feed Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 000C
  • Description: SCAN MOTOR ERROR
  • Causes: Feed Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.) Feed Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0010
  • Description: SCAN MOTOR ERROR
  • Causes: Scan Motor Deviation Error (The order from the CPU does not match the feedback of the Scan Motor.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0010
  • Description: Network I/F Initialize has not been completed.
  • Causes: Network I/F does not work correctly. Firmware for Network I/F is not installed.
  • Troubleshooting Guides: Check the fi rmware is installed into Network I/F. Main Board replacement
  • Code: 0040
  • Description: SCAN MOTOR ERROR
  • Causes: Scan Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0050
  • Description: SCAN MOTOR ERROR
  • Causes: Scan Motor Deviation Error (The order from the CPU does not match the feedback of the Scan Motor.) Scan Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0080
  • Description: SCAN MOTOR ERROR
  • Causes: Scan Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0090
  • Description: SCAN MOTOR ERROR
  • Causes: Scan Motor Deviation Error (The order from the CPU does not match the feedback of the Scan Motor.) Scan Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 00C0
  • Description: SCAN MOTOR ERROR
  • Causes: Scan Motor Overcurrent Error 1 (Big load is put on the motor movement instantaneously.) Scan Motor Overcurrent Error 2 (A little load is put on the motor movement for a long time.)
  • Troubleshooting Guides: < External factors > 1. Media Jamming 2. Pull or move the carriage by hands. 3. Carriage runs into a thing or hands. 4. Media is stuck because it is caught by the paper pipe. 5. Media is pulled forcedly. 6. Too heavy media is loaded. < Machine factors > 1. The grease lubrication of the motor gear is not enough. 2. Motor is broken or end of life. 3. Servo board is broken. 4. Tool carriage fi xation to the belt is loose. 5. The bearing inside the idle pulley is worn out. 6. The carriage belt loses steps. (The symptom may be improved by greasing the belt.) 7. Limit position is not appropriate. (When the limit position is not correctly set, it may cause a scan motor error.) 8. Power supply for motor is broken. (When the power supply voltage for the motor is not supplied, the motor cannot move and it results in the motor error. )
  • Code: 0101
  • Description: Limit Position Initialize in the Service Mode has not been done.
  • Causes: Limit Position Initialize has not been done. Limit Position Initialize is ended before it is completed.
  • Troubleshooting Guides: Complete Limit Position Initialize correctly.
  • Code: 0102
  • Description: Head Lock Sensor is ON when it should be OFF, or vice versa.
  • Causes: Head Lock Sensor does not work correctly or is broken. Head Carriage is not located at the correct position.
  • Troubleshooting Guides: Head Lock Sensor replacement Check the mechanical backlash or loose with the scan axis related parts.
  • Code: 0103
  • Description: Limit Sensor is ON when it should be OFF, or vice versa.
  • Causes: Limit Sensor does not work correctly or is broken. Tool Carriage is not located at the correct position.
  • Troubleshooting Guides: Limit Sensor replacement Check the mechanical backlash or loose with the scan axis related parts. Revised 1
  • Code: 0105
  • Description: Tool Carriage Connection Error
  • Causes: Fault of Tool Carriage Connection Loose of Connection Part Fault of the Limit Position Initialize value Limit Sensor does not work correctly or is broken.
  • Troubleshooting Guides: Check the mechanical Backlash or loose with the Tool Carriage part. Connection Part Replacement Limit Position Initialize
  • Code: 0106
  • Description: Machine fails to disconnect the Tool Carriage from the Head Carriage.
  • Causes: Fault of Tool Carriage Connection Loose of Connection Part Fault of the Limit Position Initialize value Limit Sensor does not work correctly or is broken.
  • Troubleshooting Guides: Check the mechanical Backlash or loose with the Tool Carriage part. Connection Part Replacement Limit Position Initialize
  • Code: 0107
  • Description: Linear Encoder Setup has not been done.
  • Causes: Linear Encoder Setup has not been done. Linear Encoder Setup is ended before it is completed.
  • Troubleshooting Guides: Carry out Linear Encoder Setup in service menu.
  • Code: 0109
  • Description: Wiper unit does not work correctly.
  • Causes: Wiper Unit hits the Tool Carriage Wiper Motor error Defect of Wiper Unit Defect of Wiper Sensor Cut-line or short-circuit of cable and Flexible cable
  • Troubleshooting Guides: Move the Head Carriages on the bed not to hit the Wiper Unit. Wiper Motor Replacement Wiper Unit Replacement Wiper Sensor Replacement Cable and Flexible Cable Replacement
  • Code: 0110
  • Description: Input value from Linear Encoder is not changed by the Linear Encoder origin setup. When Motor stops during printing, expected movement is not completed on some head.
  • Causes: Read error of Linear Encoder Read error of Encoder on Scan Motor side Belt is not fi xed to Head Carriage fi rmly.
  • Troubleshooting Guides: Confi rm whether Encoder Scale is in the slit of Encoder Module in a whole width of the machine. Check cable connection between Linear Encoder Board and Main Board. Confi rm connection between Belt and Tool Carriage. Linear Encoder replacement Scan Motor replacement Servo Board replacement Main Board replacement
  • Code: 0111
  • Description: This error occurs when the machine performs the Auto Crop Mark Detection before performing Crop- Cut Adjustment.
  • Causes: Crop-Cut Adjustment in the Service menu has not been performed.
  • Troubleshooting Guides: Carry out Crop-Cut Adjustment in service menu.
  • Code: 0112
  • Description: Communication error with Cartridge IC driver
  • Causes: Cartridge IC driver is broken. Cartridge IC driver cable has short circuited or cut-line.
  • Troubleshooting Guides: Ink cartridge IC sensor replacement
  • Code: 0130
  • Description: There is a problem with Thermistor for Print Heater.
  • Causes: Thermistor cable has short circuited or cutline. Thermistor has a problem.
  • Troubleshooting Guides: Check cable connection around Thermistor. Thermistor replacement
  • Code: 0135
  • Description: Print Heater temperature has reached 60°C and above.
  • Causes: Print Heater Cable connection has a problem. Thermostat has a problem. Thermistor has a problem.
  • Troubleshooting Guides: Check Print Heater. Check Thermostat. Check Thermistor.
  • Code: 0140
  • Description: There is a problem with Thermistor for dryer.
  • Causes: Thermistor cable has short circuited or cutline. Thermistor has a problem.
  • Troubleshooting Guides: Check Cable connection around Thermistor. Thermistor replacement
  • Code: 0145
  • Description: Dryer temperature has reached 80°C and above.
  • Causes: Dryer cable connection has a problem. Thermostat has a problem. Thermistor has a problem.
  • Troubleshooting Guides: Check Dryer. Check Thermostat. Check Thermistor.
  • Code: 0250
  • Description: There is a problem with Head device.
  • Causes: Head is broken.
  • Troubleshooting Guides: Head replacement

About Canon Servie Tool V5610

Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.

Canon Service Tool V5610

– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.

Canon Service Tool V5610 Functions

– Fix Canon printer 7 times/ 8 times red light blinking:

Fix 7 times/ 8 times red light blinking

– Fix Canon printer error code: 5B00, 5B01, 1700, 1701

Fix error code: 5B00, 5B01, 1700, 1701

Enter Service Mode on Canon Printer

1. Turn off a printer
2. Press and hold the Resume/Cancel/Stop button
3. Press and hold the ON button (do not release both buttons)
4. Release the Resume/Cancel/Stop button (do not release the ON button)
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.

For more information about Canon Serice Tool V5610

Contact us to get support with Roland VS540 VersaCamm Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/

Filed Under: error code, RolandTagged With: Canon Service Tool, fix Roland VS540 VersaCamm, Roland VS540 VersaCamm Error, Roland VS540 VersaCamm repair service, Roland VS540 VersaCamm troubleshooting

Most encountered printing issue

{{ faq1.title

If you see a roland camm 1 pro motor error on your computer, it’s time to learn these troubleshooting methods.

Fix PC Errors in Minutes

  • 1. Download and install Restoro
  • 2. Launch the application and select your language
  • 3. Follow the on-screen instructions to start a scan of your computer
  • Click here to get a complimentary download that will help you speed up your PC.

    Symptom
    • I am displaying an error in the magnet generator on the control panel screen.

    Cause
    • A drive error can have several causes, see below for possible options.

    Solutions

    Fix PC Errors in Minutes

    Is your computer running slow? Is it plagued with weird error messages and strange system behavior? If so, there's a good chance that you need Restoro. This powerful software will quickly and easily repair common Windows errors, protect your data from loss or corruption, and optimize your system for maximum performance. So don't suffer with a slow, frustrating PC any longer - download Restoro today!


    â € ‹1. The weight of the material, the role is too heavy. Please read this special user manual on the back and make sure this maximum weight applies to your model

    2. The carrier brake is activated and causes a serious engine malfunction. Release the brake in the media feed area on the back of the knife. Repeat the process without the service brake.

    3. Dirty dissolving roller. Remove material and inspect the sanding roller segments. Gently wiggle the roller by hand to open the curling iron around its entire circumference. Use a soft bristled brush to remove dirt. Never use a suitable wire brush as this will undoubtedly damage the grain segments. The grain reel shaft is an integral part of the overall frame, has important alignment on the production line and cannot be replaced.

    roland camm 1 pro motor error

    4. ProblemThis may be related to the characteristics of the motor in question, the internal gears, or the life of our motor. Contact your Roland dealer and / or authorized service center for assistance.

    • Code: 0001
    • Description: Occurs when the motor cannot be controlled.
    • Reasons: The output voltage (41 V) of the switching power supply is not so high. The cable feed is not properly engaged. / The power cord is damaged. The driver IC motor still on the motherboard is broken.
    • Remedy: Replace the power switch box. Connect the cable to a power source. / Replace the power cord.
    • Code: 0004
    • Description: Occurs when a large current flows towards the power supply during acceleration.
    • Reasons: If the entire cut is started without feed, this method causes an overload as some of the roll sheets are pulled out of the shaft. A heavy blade like Sand the Blast is used in precision mode at normal or high speed. Force roller movementgreat because of the large size.
    • Remedy: Turn each of our power switches back on. And then turn up the power before cutting. Use heavy duty or lower each VS value. Turn off the power switch and look for a factor, partly in the form of sheet metal shards, to see a motor failure or mainly a bearing. Then make sure someone has turned off the breaker when disconnecting the Y motor cable before checking.
    • Code: 0008
    • Description: Occurs when an overcurrent occurs during heavy movement in the feed direction.
    • Causes: If the created one is started without feeding, an overload occurs due to the roll sheet being pulled by the shaft. Heavy sheet metal such as Sand the full Blast can be used in Normal or Super Fast mode. The motion of the sanding roller is difficult due to overload.
    • Remedy: Turn the power switch back on. And then make a precise pull towards the front of the cut. Invest in heavy duty or lower your VS value. Turn off the breakerPower supply and locate the postman, such as sheet metal pieces, an engine, or a broken bearing. Then be sure to reverse the direction of the switch and disconnect the Y-cable of the motor before checking.
    • Code: 0040
    • Description. Occurs when, possibly, a large current flows in the direction of the vehicle due to acceleration.
    • Reasons: bedding stuck. The tool trolley is difficult to move due to overload.
    • Solution: adjust your hand correctly so that the game does not sag. Turn off the power switch and look for the postman who looks like pieces of sheet metal breaking the motor. Then be optimistic, turn off the power and disconnect all X motors from the mains before checking.
    • Code: 0080
    • Description. It occurs even if a large current flows, and a steady movement occurs in the direction of the carriage.
    • Reasons: sheet is jammed. Moving part of the tool cart is only difficult because of overloading.
    • Remedy: Insert the sheet carefully without a gap. OffTurn on that power switch and look for an ingredient, such as website fragments, that damages the engine. Then remember to turn off the power and disconnect the specific wire from the X-Motor before testing.
    • Code: 2000
    • Description: DDA communication error.
    • Causes: Communication error occurs when motherboard IC4 or IC22 is defective. He joined in the cause of the engine failure.
    • Remedy: Replace the motherboard.
    Click here to get a complimentary download that will help you speed up your PC.

    Erreur Moteur Roland Camm 1 Pro
    Roland Camm 1 Pro 모터 오류
    Roland Camm 1 Pro Motorfout
    Roland Camm 1 Pro Motor Error
    Roland Camm 1 Pro Motorfehler
    Errore Del Motore Roland Camm 1 Pro
    Roland Camm 1 Pro Error De Motor
    Oshibka Dvigatelya Roland Camm 1 Pro

    Post navigation

    We have noticed an unusual activity from your IP 62.89.30.2 and blocked access to this website.

    Please confirm that you are not a robot.

    spaceless }}

    {{ faq1.title decodeURIComponent spaceless }}

    xerox adc not confirm error {{ faq1.title decodeURIComponent

    6-10 MOTOR ERROR

    NO

    CHECKING POINT

    1

    Media Jam

    Broken / life of the

    2

    Motor

    Power Supply

    3

    voltage for Motor is

    not supplied

    4

    Broken Motor Driver

    There is a dirt in

    5

    teeth of Drive Gear.

    Weight of Media

    6

    exceeds usable

    Media.

    MOTOR ERROR

    < ERROR DESCRIPTION

    SCAN MOTOR ERROR

    CODE :

    < ERROR LIST >

    Bit

    No.

    Feed Motor Deviation Error

    0001

    Feed Motor Overcurrent Error 1

    (Big load is put on the motor movement

    0004

    Feed Motor Overcurrent Error 2

    (A little load is put on the motor

    0008

    movement for a long time.)

    0001 and 0004 occurred at the same

    0005

    Revised 4

    0001 and 0008 occurred at the same

    0009

    0010

    Scan Motor Deviation Error

    Scan Motor Overcurrent Error 1

    0040

    (Big load is put on the motor movement

    Scan Motor Overcurrent Error 2

    (A little load is put on the motor

    0080

    movement for a long time.)

    0010 and 0040 occurred at the same

    0050

    Revised 4

    0010 and 0080 occurred at the same

    0090

    ACTION

    Remove cause of

    Media Jam.

    Motor

    Replacement

    Replace Switching

    Power Supply

    Mainboard

    Replacement

    Clean Drive Gear.

    Use usable Media.

    0000

    0000

    Record for LAST ERROR

    CURRENT ERROR

    MEANING

    instantaneously.)

    time.

    time.

    instantaneously.)

    time.

    time.

    REFERENCE

    When the edges of the media curls or the media

    absorbs the Ink and becomes to be irregular

    surface of the media, feed motor error code 0008 0008, the Head Carriage catches

    on the media during printing and results in the

    Motor Error.

    [3-5 Carriage

    When the Motor is broken or reaches its life, the

    Motor

    Motor cannot obey the order from the CPU and it

    Replacement]

    results in the Motor Error.

    [3-13 SW Power

    When the Power Supply voltage for the Motor is

    Supply

    not supplied, the Motor cannot move and it results

    Replacement]

    in the Motor Error.

    When the Servo Board is broken, the Power

    Supply voltage for the Motor is not supplied and

    the Motor cannot move. It results in the Motor

    Error.

    When there is a dirt in the teeth of the Drive Gear

    and it cannot rotate, the Motor Error occurs.

    When the weight of Media is too heavy, the Motor

    Error occurs due to the too much load for feeding

    Media.

    Display the axis which the Error happens.

    < User side >

    1. Media Jam

    2. Pull or Move the Carriage by hands.

    3, feed motor error code 0008 0008. Carriage runs into a thing/hands.

    4. Media is stuck because the media end is not separated from the

    paper tube.

    5. Heavy media is used.

    < Mechanical Side >

    1. There is a bad contact/cut-line in the cable.

    2. Screw fixing the tool carriage to wire is shifted.

    3. Motor is broken./Life

    4. Head/Servo Board is broken.

    6-8

    OUTLINE

    CAUSE

    feed motor error code 0008 0008 We have noticed an unusual activity from your IP 62.89.30.2 and blocked access to this website.

    Please confirm that you are not a robot.

    spaceless }}

    {{ faq1.title feed motor error code 0008 0008

    0 Comments

    Leave a Comment