Canon e28 error

canon e28 error

The next time I switched on the camera, the E28 error was gone, and I proceeded to take a full 64 MB of pictures without a problem. Since then. Canon i-SENSYS MF3010 Common Errors ; E004, Description: Fixing heater drive circuit error (200V models only) ; E100, Description: Scanner area failure ; E000. Canon Error Code All · 1: Power off printer · 2: Press and hold RESUME then press POWER, The indicator will start blinking. · 3: While the.

Canon e28 error - think, that

Error code ของ Canon

E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
E8 Waste ink absorber full, or platen waste ink absorber full

E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

Clear Buffer
==========
Clear Buffer Printer Canon PIXMA IP Series IP3000 IP3300 IP3500
ถ้าขึ้นไฟกระพริบ 16 ครั้ง(หมึกสีหมด) กระพริบ 4 ครั้ง (หมึกดำหมด) ให้กด Resume ค้าง 5 วินาที

Canon inkjet Printer PIXMA iP1500
Waste Ink Counter Reset.

Canon inkjet printer PIXMA iP1000
Waste Ink Counter Reset


Printer Canon GENERIC "S" SERIES RESET CODE
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the
"Service Mode".



(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them
unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.



Canon inkjet printer PIXMA iP1000
Waste Ink Counter Reset
Manual for Service mode

1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.




Canon inkjet Printer PIXMA iP1500
Waste Ink Counter Reset.
Manual for Service mode

1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.)
should be orange.
5. Press and release the RESUME button again, the indicator
(L.E.D.) should be green
6. Release both buttons

Clear Buffer Canon Inkjet Printer "S" Series Canon BJC-210 BJC-240 BJC

Canon BJC 1000 inkjet Printer Serie
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.






Canon BJC-2000 BJC-2100 inkjet Printer Serie
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
4: Hold down the RESUME/RESET button and plug in the AC power cord
5: Release RESUME/RESET after plugging in the AC Power cord.
6: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Press and HOLD RESUME/RESET for two seconds or more and release it.
9: Unplug AC Power Cord to set data.



Canon Inkjet Printer Series


Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265
Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650
1.Unplug Power Cord
2.Hold POWER and RESUME buttons
3.Plug in Power Cord
4.Release buttons
5 front door of printer
6.Hold the CARTRIDGE and RESUME buttons
7.Press POWER
Release all buttons after the beeps
Press CARTRIDGE once
Press RESUME


Canon inkjet Printer BJC-5000
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
4:Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN,
press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
4:Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times.
The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.



Canon inkjet Printer BJC-5100
Self Test
Switch Printer off. Hold Power for 1 beep.


Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
Press RESUME twice then Wait until the printer beeps to indicate service mode
4: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be
GREEN.
5: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times.
The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.



Canon Inkjet Printer series.
Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620
Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500


1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6: Press Power to set data



Inkjet Printer
Canon BJC-600 BJC-600e BJC-610 BJC-620
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps



Inkjet Printer

Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord


Inkjet Printer
Canon BJ-30 BJC-35v BJC-70
F14 Error Reset
1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shutoff printer
10: Unplug printer then re-plug printer


Inkjet Printer
Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart

Reset ink Counter Canon Mp150/160 Printers
======================================

Befor Clear buffer Printers Canon inkjets printers
Enter Service Mode

Enter service Mode See code for reset belows



The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection

Heating  Heating

Solution for error code E28

- Check sensor by turning off the gas and allowing the unit to go through pre-purge and post purge cycles. While air is flowing through the burner check the burner sensor value on the display. This value should similar to the current intake air temperature. If this value is much different than the current intake air, check sensor resistance and wiring. If resistance values are out of range replace sensor. 


- If sensor is ok, check combustion, often a rich combustion setting elevates burner temperatures. Ensure there are no blockages on either the intake or the exhaust. Confirm the combustion is set to proper CO2 numbers, especially on low fire. After adjusting combustion, restart the boiler and observe the burner temperature on the display. This should be done both on high and low fire. 

E28 Error on Canon S10 - Possible Solution

There have been a few posts in this group over the last year regarding an "E28" (shutter error) which sometimes shows up on the S10 camera, but no solutions were posted. Thus, when my camera stopped working last week with the E28 error, I was quite panicked.

I found a solution, however, at least for now. On a different newsgroup, the E18 error (lens extraction error) was discussed, and one fellow suggested giving the lens a (physical) nudge. For lack of any better options, I tried this, and, to my great surprise, it worked! (The lens extracts momentarily before the E28 is displayed, after which the lens immediately recedes. It is during this momentary extraction that I nudged the lens).

The next time I switched on the camera, the E28 error was gone, and I proceeded to take a full 64 MB of pictures without a problem.

Since then, the E28 error did recur one morning. However, I used the lens-nudge trick again, and was back in business immediately.

Questions remain, however. Why does the lens nudge help? (perhaps there is some dust or sand caught in the camera which is loosened by the nudge?) Does it indicate that my camera is on its way out? And, it is hard to believe that the "nudge" is really good for the camera. I am talking about a real physcial forcible twist to the lens. Even if it just for a second, it is certainly not the expected usage. Currently, it works, so I do it, but it does worry me.

Any thoughts?

Avi Shmidman--Jerusalem, Israel

Where I am currently producing great black and white shots of the present snowstorm with my Canon S10 camera.

MAJ13/02/18 The Service Tool V3400 , and service tool V3600 , allow you to reset the waste ink pad counter on some Canon printers:  You can solve the messages errors "Waste Ink Tank Full" or "Waste Ink Pad Full", "error 5B00" or "Error P07" on these printers: Canon Pixma iP2700, iP4800, iP4810, iP4840, iP4850, iP4900, iP4910, iP4940, iP4970, iP4980, iP4990, iP5810, iP5880 Canon Pixma MP230, MP240; MP250; MP260; MP270; MP280; MP480; MP490; MP540; MP550; MP560; MP620; MP630; MP640; MP980; MP990; Canon Pixma IX6500, IX6510, IX7000 Canon Pixma IP3600, IP4940 Canon Pixma PRO9000, PRO9500 Canon Pixma MG2120. MG2140, MG2240, MG2250, MG2440, MG3240, MG3140, MG4100, MG4140, MG5140, MG5150, MG5240, MG5340, MG6140, MG6240, MG8140, MG8240  Canon MX397, MX320, MX330, MX370, MX860  etc Where can you download the Service Tool V3400 ? It is free here: https:/ /1fichier. com/ ?c198556kp0 There is too a paid version here: V3400 C

Powershot S20 and E28 error

Hello,

(Sorry for my bad English, I'm French)

Got same issue with my 3 years old S20: Error 28 + zoom which cannot retract and properly close.

It happened while the battery alarm was blinking and I tried to shoot a last picture. The S20 has suddently shut down and the zoom stayed wide opened.

When back home of course I have tried again while plugged to AC power with no result, still E28 and a strange zoom noise. I have now also tried your slapping stuff with no success!

In the meantime I have brought it to my local Canon authorized maintenance center (France) and got it back with following diag: S20 may have been hurt, they first have to replace both the S20 body and an internal circuitry, then they will have to check whether they need to also replace the whole zoom!

In the end that would cost me first about 200$ + even 100 to 200$ more for zoom replacement. No need to say that it is not worth doing it!

I would like to make two remarks because I am very angry to put my S20 back to the shell with no hope to fix it:

  • it is unacceptable that your digital camera could be out of order just because you have tried to shoot a picture while the battery was low. I already had the case before and the S20 was closing down properly before the battery would be totally exhausted. I guess it is a security action that Canon manage in order to avoid those E28 issues.

At least Canon should clearly warn their customers on this potential problem and ask them to stop shooting as soon as the battery alarm blinks!

  • Canon authorized center had very poor consideration for my problem. Furthermore I have a strong doubt on the fact that my S20 could have been hurt and damaged as I used to take special care on it and I never noticed the kick they showed to me when I got it back.

So I strongly suspect that they did it themselves and I have no way to prove it!

I don't know if this is also the case in other countries or whether it is due to the fact that S20 is now quite an old stuff they don't care about, but I know now that my next buy will be a Nikon (probably D70) and I hope they will have a better service level... in case I need it.
Anyway I will send a mail to Canon France, and see what happen ...

hoyland wrote:

hoyland wrote:

Good news Powershot S20 owners. Error E28, which seems to affect
both S10 and S20 after a couple of years can be cured. Hold camera
(lens upwards) in right hand and slap down on left hand so that it
hurts a little. THAT'S IT. After 2 weeks asking advice, reading
postings, phoning Canon helpline - who wanted £128 just to look at
it, I found this remedy for the S10. I tried it on my S 20 and it
worked immediately. One week on, it is still working. Canon wont
tell you this, so please pass it on and you might save someone over
£120.

P.S. Bad news Powershot S20 owners. The cure - slapping the camera-
worked fine but only for a few days. It has given up the ghost
again and I am looking again at new cameras.
Hoyland.

canon e28 error Powershot S20 and E28 error

Hello,

(Sorry for my bad English, I'm French)

Got same issue with my 3 years old S20: Error 28 + zoom which cannot retract and properly close.

It happened while the battery alarm was blinking and I tried to shoot a last picture, canon e28 error. The S20 has suddently shut down and the zoom stayed wide opened.

When back home of course I have tried again while plugged to AC power with no result, still E28 and a strange zoom noise. I have now also tried your slapping stuff with no success!

In the meantime I have brought canon e28 error to my local Canon authorized maintenance center (France) and got it back with following diag: S20 may have been hurt, they first have to replace both the S20 canon e28 error and an internal circuitry, then they will have to check whether they need to also replace the whole zoom!

In the end that would cost me first about 200$ + even 100 to 200$ more for zoom replacement. No need to say that it is not worth doing it!

I would like to make two remarks because I am very angry to put my S20 back to the shell with no hope to system configuration data read error gateway m-1625 it:

  • it is unacceptable that your digital camera could be out of order just because you have tried to shoot a picture while the battery was low. I already had the case before and the S20 was closing down properly before the battery would be totally exhausted, canon e28 error. I guess it is a security action that Canon manage in order to avoid those E28 issues.

At least Canon should clearly warn their customers on this potential problem and outlook express firewall error 500 them to stop shooting as soon as the battery alarm blinks!

  • Canon authorized center had very poor consideration for my problem. Furthermore I have a strong doubt on the fact that my S20 could have been hurt and damaged as I used to take special care on it and I never noticed the kick they showed to me when I got it back.

So I strongly suspect dmc-lc33 system error they did it themselves and I have no way to prove it!

I don't know if this is also the case in other countries or whether it is due to the fact that S20 is now quite an old stuff they don't care about, but I know now that my next buy will be a Nikon (probably D70) and I hope they will have a better service level. in case I need it.
Anyway I will send a mail to Canon France, and see what happen .

hoyland wrote:

hoyland wrote:

Good news Powershot S20 owners. Error E28, canon e28 error, which seems to affect
both S10 and S20 after a couple of years can be cured, canon e28 error. Hold camera
(lens upwards) in right hand and slap down on left hand so that it
hurts a little. THAT'S IT. After 2 weeks asking advice, reading
postings, phoning Canon helpline - who wanted £128 just to look at
it, I found this remedy for the S10, canon e28 error. I tried it on my S 20 and it
worked immediately. One week on, canon e28 error, it is still working. Canon wont
tell you this, so please pass it on and you might save someone over
£120.

P.S. Bad news Powershot S20 owners. The cure - slapping the camera-
worked fine but only for a few days. It has given up the ghost
again and I am looking again at new cameras.
Hoyland.

Error code ของ Canon

E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
E8 Waste ink absorber full, or platen waste ink absorber full

E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Compile error array already dimensioned vba error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

Clear Buffer
==========
Clear Buffer Printer Canon PIXMA IP Series IP3000 IP3300 IP3500
ถ้าขึ้นไฟกระพริบ 16 ครั้ง(หมึกสีหมด) กระพริบ 4 ครั้ง (หมึกดำหมด) ให้กด Resume ค้าง 5 วินาที

Canon inkjet Printer PIXMA iP1500
Waste Ink Counter Reset.

Canon inkjet printer PIXMA iP1000
Waste Ink Counter Reset


Printer Canon GENERIC "S" SERIES RESET CODE
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
succession. Note: you are still holding the POWER canon e28 error. The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the
"Service Mode".



(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with canon mp210 error code 16 key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them
unaltered - Canon e28 error have been warned!)
After selecting the desired mode (eg 4), canon e28 error, press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.



Canon inkjet printer PIXMA iP1000
Waste Ink Counter Reset
Manual for Service mode

1, canon e28 error. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME buttonthe indicator canon e28 error should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.




Canon inkjet Printer PIXMA iP1500
Waste Ink Counter Reset.
Manual for Service mode

1. Turn off the printer, canon e28 error. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3, canon e28 error. The indicator (L.E.D.) should be green.
4. Press and release the RESUME buttonthe indicator (L.E.D.)
should be orange.
5. Press and release the RESUME button again, the indicator
(L.E.D.) should be green
6. Release both buttons

Clear Buffer Canon Inkjet Printer "S" Series Canon BJC-210 BJC-240 BJC

Canon BJC 1000 inkjet Printer Serie
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.






Canon BJC-2000 BJC-2100 inkjet Printer Serie
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
4: Hold down the RESUME/RESET button and plug in the AC power cord
5: Release RESUME/RESET after plugging in the AC Power cord.
6: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Press and HOLD RESUME/RESET for two seconds or more and release it.
9: Unplug AC Power Cord to set data.



Canon Inkjet Printer Series


Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265
Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650
1.Unplug Power Cord
2.Hold POWER and RESUME buttons
3.Plug error stray 321in program Power Cord
4.Release buttons
5 front door of printer
6.Hold the CARTRIDGE and RESUME buttons
7.Press POWER
Release all buttons after the beeps
Press CARTRIDGE once
Press RESUME


Canon inkjet Printer BJC-5000
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking
4:Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, canon e28 error,
press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking
4:Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times.
The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON, Press and hold RESUME until the printer plays a melody of beeps.



Canon inkjet Printer BJC-5100
Self Test
Switch Printer off. Hold Power for 1 beep.


Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
Press RESUME twice then Wait until the printer beeps to indicate service mode
4: When the indicator lights steady GREEN, canon e28 error, press RESUME four(4)times. The indicator should be
GREEN.
5: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
Press RESUME twice then Wait until the printer beeps to canon error 5100 service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times.
The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON, Press and hold RESUME syntax error c masm the printer plays a melody of beeps.



Canon Inkjet Printer series.
Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620
Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500


1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6: Press Power to set data



Inkjet Printer
Canon BJC-600 BJC-600e BJC-610 BJC-620
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps



Inkjet Printer

Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord


Inkjet Printer
Canon BJ-30 BJC-35v BJC-70
F14 Error Reset
1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press Canon e28 error to shutoff printer
10: Unplug printer then re-plug printer


Inkjet Printer
Canon BJ F900, F890, F700, F500, canon e28 error, S900, S820, S750 and S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, canon e28 error, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4, canon e28 error. Clear the waste-ink counter
5, canon e28 error. Printer model setting, canon e28 error. (more selections beyond this- leave this alone)
After selecting mode, canon e28 error, press the POWER button to commit the change, and return to the top of the function selection menu, canon e28 error. Pressing the POWER button again turns off the printer for a restart

Reset ink Counter Canon Mp150/160 Printers
======================================

Befor Clear buffer Printers Canon inkjets printers
Enter Service Mode

Enter delphi indy socket error 10053 Mode See code for reset belows



The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection

MAJ13/02/18 The Service Tool V3400and service tool V3600allow you to reset the waste ink pad counter on some Canon printers:  You fatal error call to undefined function commrating solve the messages errors "Waste Ink Tank Full" or "Waste Ink Pad Full", "error 5B00" or "Error P07" on these printers: Canon Pixma iP2700, iP4800, iP4810, iP4840, iP4850, iP4900, iP4910, iP4940, iP4970, iP4980, iP4990, iP5810, iP5880 Canon Pixma MP230, MP240; MP250; MP260; MP270; MP280; MP480; MP490; MP540; MP550; MP560; MP620; MP630; MP640; MP980; MP990; Canon Pixma IX6500, IX6510, IX7000 Canon Pixma IP3600, IP4940 Canon Pixma PRO9000, PRO9500 Canon Pixma MG2120. MG2140, MG2240, MG2250, MG2440, MG3240, MG3140, MG4100, MG4140, MG5140, MG5150, MG5240, canon e28 error, MG5340, MG6140, MG6240, MG8140, canon e28 error, MG8240  Canon MX397, MX320, MX330, MX370, MX860  etc canon e28 error Where can you download the Service Tool V3400 ? It is free here: https:/ /1fichier. com/ ?c198556kp0 canon e28 error There is too a paid version here: V3400 C

When Error Occurred

Error Code

Support Code

Cause

Action

E02

1000

3442

3443

3444

3445

Printer is out of paper.

Printing one side is complete if you are performing manual duplex printing.

  • If the printer is out of paper:

  • If you are performing manual duplex printing:

    Prepare to print the other side following the instructions on the computer screen.

E03

1203

1300

Cover is opened during printing.

Paper is jammed when feeding paper canon e28 error rear tray.

  • If the cover is open:

  • If paper is jammed:

E04

168A

FINE cartridge is not installed.

E05

1401

1403

1430

1485

Ink cartridge cannot microsoft office ole error 800a03ec recognized.

Check the following.

  • if the color FINE cartridge is installed on the left side properly
  • if the black FINE cartridge is installed on the right side properly
  • Model number of canon e28 error FINE cartridge

If the above does not resolve the problem, replace the FINE cartridge with a new one.

E08

1700

1701

1712

1713

1714

1715

Ink absorber is almost full.

E09

1890

Shipping tape or protective material may still be attached to FINE cartridge holder.

E11

4102

4103

Cannot perform printing with current print settings.

E12

4100

Specified data cannot be printed.

E13

1686

The ink may have run out.

E14

1684

The ink cartridge cannot be recognized.

E15

1682

FINE cartridge cannot be recognized.

E16

1688

The ink has run out.

E23

3446

IP address and subnet mask are conflicting.

E31

Failed in Wi-Fi setup.

Press the printer's OK button to resolve the error.

If you are performing setup with WPS:

  1. Check the security settings and perform setup again.

  2. Perform setup using another setup method.

E32

Cannot find a wireless router during setup.

Press the printer's OK button to resolve the error.

Perform Wi-Fi setup again.

E33

Cannot connect because multiple wireless routers are connecting to the printer.

Press the printer's OK button to resolve the error.

Perform Wi-Fi setup again after a while (about 2 minutes).

If the above does not resolve the problem, refer to the instruction manual supplied with the wireless router.

E34

3440

Easy wireless connect has failed.

E36

3441

Easy wireless connect has failed.

E37

Failed in Wi-Fi setup.

Press the printer's OK button to resolve the error.

Turn off the wireless router and turn it back on, and then perform setup again.

If the above does not resolve the problem, refer to the instruction manual supplied with the wireless router and check the settings.

E38

Cannot connect to a wireless router.

Cannot change the LAN settings.

Press the printer's OK button to resolve the error.

Check the following.

  • if the printer's Wi-Fi is enabled
  • if you select a proper wireless router to connect
  • if the password you entered is correct
  • if the specified network name (SSID) is correct

After checking the above, turn off the wireless router and turn it on again.

You cannot change LAN settings while you are using LAN.Change them when you are not using LAN.

E39

495A

An error occurred while communicating via Wi-Fi or while in standby.

E45

Cannot connect canon mp210 error code 16 network.

Press the printer's OK canon e28 error to resolve the error.

Check the LAN connection and network settings.

Connection may be successful after a while.

E46

Cannot connect to Internet.

Press the printer's OK button to resolve the error.

Check the wireless router settings.

E47

Cannot connect to server.

Press the printer's OK button to resolve the error and perform operations again after a while.

E48

Cannot connect to server.

Press the printer's OK button to resolve the error and perform operations again after a while.

E49

Failed in connecting to Internet because network connection is being prepared.

Press the printer's OK button to resolve the error and perform operations again after a while.

E50

Failed in acquiring contents.

Press the printer's OK button to resolve the error and perform operations again after a while.

E51

Cannot connect to server.

Press the printer's OK button to resolve the error and perform operations again after a while.

E54

Only information registered to the printer is deleted because of failing to connect IJ Cloud Printing Center.

Press the printer's OK button to resolve the error.

Delete registered information of IJ Cloud Printing Center from your computer or smartphone.

E55

The printer is already registered to IJ Cloud Printing Center.

Press the printer's OK button to resolve the error.

Delete registered canon e28 error of IJ Cloud Printing Center and register the printer again.

E56

The online service is not available in your region.

Press the printer's OK button to resolve the error.

Contact the provider for where the online service is available.

E57

2900

Scanning print head alignment sheet failed.

E58

Trying to start copying before you register the paper size.

Register the paper size and start copying.

Press the Stop button to cancel copying.

E59

2114

Paper size settings at printer driver do not match the canon e28 error size registered in the printer.

E61

3412

Scanning original has failed.

E62

Unexpected error occurred while scanning is in progress.

Press the printer's OK button to resolve the error.

Change settings and perform operations again.

E63

Reached the upper limit of pages which can be saved.

Press the printer's OK button to resolve the error.

No more pages can be saved in one file.

Save the rest as different one.

E64

Scanning original has failed.

Original is not placed on the platen or the original cannot be scanned.

Press the printer's OK button to resolve the error and check the following.

  • Make sure the original is placed on the platen.
  • Make sure the original is set in the correct position and orientation.

After checking the above, perform operations again.

E65

Saving scanned data failed because the printer's memory is full.

Press the printer's OK button to resolve the error.And then, take measures below.

  • Reduce the resolution and rescan the original.
  • Reduce the amount of original to be scanned at canon e28 error time.

P02

5100

Printer error has occurred.

P03

6000

Printer error has occurred.

P07

5B00

5B01

5B12

5B13

5B14

5B15

Printer error has occurred.

P08

P09

P20

P22

P26

P27

P28

P29

5011

5012

5050

5200

5205

5206

6500

6800

6801

6900

6901

6902

6910

6911

6930

6931

6932

6933

6936

6937

6938

6940

6941

6942

6943

6944

6945

6946

Printer error has occurred.

Turn off the printer and unplug it.

Plug in the printer again and turn it back on.

If this does not solve the problem, contact your nearest Canon service center to request a repair.

P10

B202

B203

B204

B205

An error requiring a repair has occurred.

Turn off the printer and unplug it.

Contact your nearest Canon service center to request a repair.

E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink (กดปุ่ม Resume ค้าง 5 วินาทีก็สามารถพิมพ์ต่อได้)
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
(E5 นี่อาการหนัก ถ้าเช็ดทำความสะอาดหน้าสัมผัสแล้วไม่หายก็ต้องซื้อตลับใหม่)

E7 (สำหรับรุ่น iP1880) ตลับเสีย


E8 Waste ink absorber full, or platen waste ink absorber full

E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E14 นี่ก็อาการหนัก ต้องเข้า service halt on all errors in bios ถึงจะพิมพ์ได้
E15 Ink cartridge is not installed
E16 canon e28 error Ink remaining is unknown .(iP1800 ให้กด resume ค้าง 5 วินาที)
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise canon e28 error E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

Clear Buffer
==========
Clear Buffer Printer Canon PIXMA IP Series IP3000 IP3300 IP3500
ถ้าขึ้นไฟกระพริบ 16 ครั้ง(หมึกสีหมด) กระพริบ 4 ครั้ง (หมึกดำหมด) ให้กด Resume ค้าง 5 วินาที

Canon inkjet Printer PIXMA iP1500
Waste Ink Counter Reset.

Canon inkjet printer PIXMA iP1000
Waste Ink Counter Reset


Printer Canon GENERIC "S" SERIES RESET CODE
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
succession. Note: you are still holding the POWER button), canon e28 error. The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the
"Service Mode".

 

(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them
unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to canon e28 error top of the function selection menu. Press the POWER button again to restart the printer.

 

Canon inkjet printer PIXMA iP1000 iP1800
Waste Ink Counter Reset
Manual for Service mode

1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME buttonthe indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
canon e28 error. Release both buttons.
พอเข้า Service mode ได้สำเร็จ ก็เปิดโปรแกรม iPtool กดปุ่ม clear track_errors = on  


Canon inkjet Printer PIXMA iP1500
Waste Ink Counter Reset.
Manual for Service mode

1, canon e28 error. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3, canon e28 error. The indicator (L.E.D.) should be green.
4. Press and release the RESUME buttonthe indicator (L.E.D.)
should be orange.
5. Press and release the RESUME button again, canon e28 error indicator
(L.E.D.) should be green
6. Release both buttons

Clear Buffer Canon Inkjet Printer "S" Series Canon BJC-210 BJC-240 BJC

Canon BJC 1000 inkjet Printer Serie
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds droid x2 error bp pass more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.

run time error 3027 transferspreadsheet  


Canon BJC-2000 BJC-2100 inkjet Printer Serie
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
4: Hold down the RESUME/RESET button and plug in the AC power cord
5: Release RESUME/RESET after plugging in the AC Power cord.
6: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Press and HOLD RESUME/RESET for two seconds or more and release it.
9: Unplug AC Power Cord to set data.

 

Canon Inkjet Printer Series


Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265
Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650
1.Unplug Power Cord
2.Hold POWER canon e28 error RESUME buttons
3.Plug in Power Cord
4.Release buttons
5 front door of printer
6.Hold the CARTRIDGE and RESUME buttons
7.Press POWER
Release all buttons after the beeps
Press CARTRIDGE once
Press RESUME


Canon inkjet Printer BJC-5000
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
4:Press RESUME twice then Wait until the printer beeps to error correct *.map files not found service mode
5: When the indicator lights steady GREEN,
press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, canon e28 error, The indicator will start blinking.
3: While the indicator is blinking ,
4:Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times.
The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON, Press and hold RESUME until the printer plays a melody of beeps.

 

Canon inkjet Printer BJC-5100
Self Test
Switch Printer off, canon e28 error. Hold Power for 1 beep.


Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
Press RESUME twice then Wait until the printer beeps to indicate service mode
4: When the indicator lights steady GREEN, press RESUME four(4)times, canon e28 error. The indicator should be
GREEN.
5: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, canon e28 error, The indicator will start blinking.
3: While the indicator is blinking ,
Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights server fatal error code 13 GREEN, press RESUME two(2)times.
The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ONcanon e28 error,Press and hold RESUME until the printer plays a melody of beeps.

 

Canon Inkjet Printer series.
Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620
Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500


1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6: Press Power to set data

 

Inkjet Printer
Canon BJC-600 BJC-600e BJC-610 BJC-620
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps

 

Inkjet Printer

Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord


Inkjet Printer
Canon BJ-30 BJC-35v BJC-70
F14 Error Reset
1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Canon e28 error POWER 3ds max 2009 error 0xc0150002 printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shutoff printer
10: Unplug printer then re-plug printer


Inkjet Printer
Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
Release the RESUME button, then press and release the RESUME button two more times in succession, canon e28 error. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4, canon e28 error. Clear the canon e28 error counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart

Reset ink Counter Canon Mp150/160 Printers
======================================

Befor Clear buffer Printers Canon inkjets printers
Enter Service Mode

Enter service Mode See code for reset belows

 

The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection

 

Canon PIXMA iP4200 4300 6700 printer
=============================

Service Call Errors (by Cyclic Blinking in Orange (Alarm LED) and Green (Power LED), or Alarm LED Lit in Orange)

Service call errors are indicated by the number of cycles the Alarm and Power LEDs blink, and the corresponding error code is displayed on the LCD.

Cycles of blinking in orange (Alarm LED) and green(Power LED):

2 times Carriage error [5100] An error occurred in the carriage encoder signal.
Replacement
- Carriage unit (QM2-2298)
- Timing slit strip film (QC1-6394)
- Logic board ass'y (QM2-2745)*1
- Carriage motor (QK1-1500)

3 times Line feed error [6000] An error occurred in the line feed signal.
Replacement
- Timing sensor unit (QM2-2683)
- Timing slit disk film(QC1-6229)
- Feed roller ass'y (QL2-0925)
- Platen unit (QM2-2313)
- Logic board ass'y (QM2-2745)*1
- Paper feed motor (QK1-1502)


Cycles of blinking in orange (Alarm LED) and green(Power LED):
4 times Purge cam sensor error [5C00] An error occurred in the purge unit.

Replacement
- Purge unit (QM2-2299)
- Logic board ass'y (QM2-2745)*1

5 times ASF (cam) sensor error [5700]
This error takes place when feeding paper
from the ASF after an error occurred in the
ASF cam sensor.

Replacement
- Sheet feed unit (QM2-2312)

6 times Internal temperature error[5400]
The internal temperature is not proper.

Replacement
- Logic board ass'y (QM2-2745)*1

7 times Waste ink absorber full [5B00]
The waste ink absorber is full.
Replacement
- Ink canon e28 error kit (QY5-0147)

8 times Print head temperature rise error [5200]
The print head temperature exceeded the specified value.

Replacement
- Print head (QY6-0063)
- Logic board ass'y (QM2-2745)*1

9 times EEPROM error [6800] A problem occurred in writing to the EEPROM.
Replacement
- Logic board ass'y (QM2-2745)*1

11 times Carriage lift mechanism error [5110]
The carriage did not move up or down properly.

Replacement
- PR lift shaft ass'y (QL2-0936)
- Sheet feed unit (QM2-2312)
- Vba is error board ass'y (QM2-2745)*1
- Carriage lift sensor unit (QM2-2678)

12 times AP position error [6A00] An error occurred in the Medisana error 3 motor during purging operation.
Replacement
- Sheet feed unit (QM2-2312)
- Logic board ass'y (QM2-2745)*1
- Purge unit (QM2-2208)

13 times Paper feed position error [6B00]
An error occurred in the paper feed motor.

Replacement
- Sheet feed unit canon e28 error - Logic board ass'y (QM2-2745)*1

14 times Paper feed cam sensor error [6B10]
An error occurred in the paper feed cam sensor
during paper feeding from the front paper feed cassette.

This error is also indicated when the waste ink counter is 60% or more, and a paper jam occurs.
Replacement
- Sheet feed unit (QM2-2312)
- Logic board ass'y (QM2-2745)*1

15 times USB Host VBUS overcurrent [9000]
The USB Host VBUS is overloaded.
Replacement
- Logic board ass'y (QM2-2745)*1

16 times Valve sensor error [6C00] An error occurred in the valve sensor during cleaning.

Replacement
- Logic board ass'y (QM2-2745)*1
- Purge unit (QM2-2208)

17 times Motor driver error [6D00] The AD conversion value indicating the motor
driver temperature is not proper.
Replacement
- Logic board ass'y (QM2-2745)*1

19 times Ink tank position sensor error [6502]
None of the ink tank position is detected.

Replacement
- Platen unit (QM2-2313)
- Logic board ass'y (QM2-2745)*1

20 times Other hardware error [6500] The PCI bus error is detected by the ASIC.

Replacement
- Logic board ass'y (QM2-2745)*1

canon e28 error

0 Comments

Leave a Comment