Ami bios error beeps

ami bios error beeps

When AMIBIOS performs the Power On Self Test, it writes diagnostic codes checkpoint codes to I/O port 0080h. If the computer cannot complete the boot. A single short beep from an AMI-based BIOS means. 1 Beep - Refresh Failure. Reseat/replace memory, troubleshoot motherboard. ; 2 Beeps - Parity Error. Reseat/replace memory, troubleshoot motherboard. ; 3 Beeps -. ami bios error beeps

Beeps

Error Message

Description

1-1-2CPU test failureThe CPU is faulty.  Replace the CPULow 1-1-2System board select failureThe motherboard is having an undetermined fault.  Replace the motherboard1-1-3CMOS read/write errorThe real time clock/CMOS is faulty.   Replace the CMOS if possibleLow excessive crc/alignment errors CMOS RAM failureThe extended portion of the CMOS RAM has failed.  Replace the CMOS if possible1-1-4BIOS ROM checksum errorThe BIOS ROM has failed.  Replace the BIOS or upgrade if possible1-2-1PIT failureThe programmable interrupt timer has failed.  Replace if possible1-2-2DMA failureThe DMA controller has failed.   Replace the IC if possible1-2-3DMA 1618 msi error failureThe DMA controller has failed.   Replace the IC if possible1-3-1RAM refresh failureThe RAM refresh controller has failed1-3-264KB Ami bios error beeps failureThe test of the first 64KB RAM has failed to start1-3-3First 64KB RAM failureThe first RAM IC has failed, ami bios error beeps.   Replace the IC if possible1-3-4First 64KB logic failureThe first RAM control logic has failed1-4-1Address line failureThe address line to the first 64KB RAM has failed1-4-2Parity RAM failureThe first RAM IC has failed.   Replace if possible1-4-3EISA fail-safe timer testReplace the motherboard1-4-4EISA NMI port 462 testReplace the motherboard2-1-164KB RAM failureBit 0; This data bit on the first RAM IC has failed.  Replace the IC if possible2-1-264KB RAM failureBit 1; This data bit on the first RAM IC has failed.  Replace the IC if possible2-1-364KB Ami bios error beeps failureBit 2; This data bit on the first RAM IC has failed.  Replace the IC if possible2-1-464KB RAM failureBit 3; This data bit on the first RAM IC has failed.  Replace the IC if possible2-2-164KB RAM failureBit 4; This data bit on the first RAM IC has failed.  Replace the IC if possible2-2-264KB RAM failureBit 5; This data bit on the first RAM IC has failed.  Replace the IC if possible2-2-364KB RAM failureBit 6; This data bit on the first RAM IC has failed.  Replace the IC if possible2-2-464KB RAM failureBit 7; This data bit on the first RAM IC has failed.  Replace the IC if possible2-3-164KB RAM failureBit 8; This data bit on the first RAM IC has failed.  Replace the IC if possible2-3-264KB RAM failureBit 9; This data bit on the first RAM IC has failed.  Replace the IC if possible2-3-364KB RAM failureBit 10; This data bit on the first RAM IC has failed.  Replace the IC if possible2-3-464KB RAM failureBit 11; This data bit on the first RAM IC has failed.  Replace the IC if possible2-4-164KB RAM failureBit 12; This data bit on the first RAM IC has failed.  Replace the IC if possible2-4-264KB RAM failureBit 13; This data bit on the first RAM IC has failed.  Replace the IC if possible2-4-364KB RAM failureBit 14; This data bit on the first RAM IC has failed.  Replace the IC if possible2-4-464KB RAM failureBit 15; This data bit on the first RAM IC has failed.  Replace the IC if possible3-1-1Slave DMA register failureThe DMA controller has failed.   Replace the controller if possible3-1-2Master DMA register failureThe DMA controller had failed.   Replace the controller if possible3-1-3Master interrupt mask register failureThe interrupt controller IC has failed3-1-4Slave interrupt mask register failureThe interrupt controller IC has failed3-2-2Interrupt vector errorThe BIOS was unable to load the interrupt vectors into memory.  Replace the motherboard3-2-3Reserved3-2-4Keyboard controller failureThe keyboard controller has failed.   Replace the IC if possible3-3-1CMOS RAM power badReplace the CMOS battery or CMOS RAM if possible3-3-2CMOS configuration errorThe CMOS configuration has failed.   Restore the configuration or replace the battery if possible3-3-3Reserved3-3-4Video memory failureThere is a problem with the video memory.  Replace the video adapter if possible3-4-1Video initialization failureThere is a problem with the video adapter.  Reseat the adapter or replace the adapter if possible4-2-1Timer failureThe system’s timer IC has failed.   Replace the IC if possible4-2-2Shutdown failureThe CMOS has failed.  Replace the CMOS IC if possible4-2-3Gate A20 failureThe keyboard controller has failed.   Replace the IC if possible4-2-4Unexpected interrupt in protected modeThis is a CPU problem.  Replace the CPU and retest4-3-1RAM test failureSystem RAM addressing circuitry is faulty.  Replace the motherboard4-3-3Interval timer channel 2 failureThe system timer IC has failed.   Replace the IC if possible4-3-4Time of day clock failureThe real time clock/CMOS has application deployment error.   Replace the CMOS if possible4-4-1Serial port failureA error has occurred in the serial port circuitry4-4-2Parallel port failureA error has occurred in the parallel port circuitry4-4-3Math coprocessor failureThe math coprocessor has failed.   If possible, replace the MPU

Beeps

Error Message

Description

1 shortDRAM refresh failureThe programmable interrupt timer or programmable interrupt controller has probably failed2 shortMemory parity errorA memory parity error has occurred in the first 64K of RAM.  The RAM IC is probably bad3 shortBase 64K memory failureA memory failure has occurred in the first 64K of RAM.  The RAM IC is probably bad 4 shortSystem timer failureThe system clock/timer IC has failed or there is a memory error in the first bank of memory5 shortProcessor errorThe system CPU has failed6 shortGate A20 failureThe keyboard controller IC has failed, which is not allowing Gate A20 to switch the processor to protected mode. Replace the keyboard controller7 shortVirtual mode processor exception errorThe CPU has generated an exception error because of a fault in the CPU or motherboard circuitry8 shortDisplay memory read/write errorThe system video adapter is missing or defective9 shortROM checksum errorThe contents of the system BIOS ROM does not match the expected checksum value.  The BIOS ami bios error beeps ROM is probably defective and should be replaced10 shortCMOS shutdown register read/write errorThe shutdown for the CMOS has failed11 shortCache errorThe L2 cache is faulty1 long, 2 shortFailure in video systemAn error was encountered in the video BIOS ROM, or a horizontal retrace failure has been encountered1 long, 3 shortMemory test failureA fault has been detected in memory above 64KB1 long, 8 shortDisplay test failureThe video adapter is either missing or defective2 shortPOST FailureOne of error clear renault clio hardware testa have failed1 longPOST has passed all tests 

Post beep codes

Approved: ASR Pro

  • 1, ami bios error beeps. Download and install ASR Pro
  • 2. Launch the application and select your language
  • 3. Follow the on-screen instructions to start a scan of your PC
  • Get the best performance from your computer with this software - download it and fix your PC today.

    There was a known bug with gigabyte beep BIOS error codes on some drives last week. This problem can arise for several reasons. We’ll look at them now, ami bios error beeps. g.3 minimum beeps: 64K base memory address display error. 4 short beeps: real time clock malfunction. 5 short beep CPU error half beep : Keypad error 7 temporary beep : CPU interrupt error 8 short ami bios error beeps : Graphic credit card error 9 short beep : Memory error 10 short beep : CMOS error 11 fast beep : Cache error – CPU memory.

    1. AWARD BIOS 1 short beep: Normal system 2 fairly short beeps : CMOS error 1 long beep and 1 short beep : Memory error One-way beep and 2 short beeps : Visa or Mastercard graphic error 1 long beep and 1 short beep Beep : AGP error 1 long beep and 9 short beeps : Memory error Permanent long beep : Memory installed incorrectly Permanent short beep : Power supply

    PRICE OF FIRST BIOS SIGNAL1 short normal system2 separate terms Beep :CMOS Error1 long beep and one particularly short beep Memory error1 long beep and 2 short beeps Visa card graphic error1 long beep and 3 fixed beeps :AGP error1 long beep in addition to 9 short beeps : Memory errorLong continuous beep : Memory connected incorrectlyShort continuous beep : Power failure2. BIOS AMI1 short beep : Memory error2 short beeps ¼ Memory parity search error.3 short beeps : Error checking 64K base memory address4 short beeps – real time fault clock.5 compact beeps – CPU error6 short beeps Keyboard monitoring7 short beeps : confused processor interrupt8 short beeps • Video card error9 Temporary buzzer : Memory error10 short beeps – CMOS error11 short beeps • Internal processor memory failure cache

    Did

    How do I turn off the beep sound in my BIOS Gigabyte?

    There is nothing in the BIOS to disable the transmit signal. Just turn off the internal speaker if ami bios error beeps can.

    What does the BIOS beep mean?
    Computer POST (Power On Self Test) verifies the compatibility and connectivity of a computer’s test equipment before starting the rest of the boot process. If the computer passes all POST tests, it may emit one significant beep.
    However, if the computer runs out of mail, depending on what is wrong, the computer will either beep or generate a real beep code to tell us what the problem is.
    You should always check your current motherboard manual to make sure we have a list of the most common beeps to help you find.

    bios error beep codes gigabyte

    BIOS BONUS
    Motherboard manufacturers have developed special BIOS software based on the AwardBIOS program. AwardBIOS based BIOS beep codes may be the same as the original AwardBIOS beep codes (see below), or may differ slightly at best.

    1 short beep – normal system
    A bachelor short beep from the award-winning BIOS at the very bottomis barely a notification that all packages have been removed. In other words, this is a whole coded beep that you need to hear, and the one that you hear the most every time you turn on your computer, since the day the user bought it. No troubleshooting required!

    2 single beeps :CMOS
    You can try reinstalling CMOS, which is best in thirteen minutes. CMOS batteries last about 5 years, so depending on the age of your system, ami bios error beeps, it might be time to replace them. They are quite cheap and simple, so you can order them online, be optimistic, they are exactly the same type (check the engraving on them and the type number).

    1 long and 7 short beeps – memory error
    Please re-insert these RAM keys or try each one to see if any of the keys are faulty. In this case, the system should function normally without the key, which should then be replaced.

    1 continuous beep and 2 beeps : Brief diagram of credit card errors
    Long beep followed only bytwo short beeps means that an error has already occurred while using the video card. Replacing the video presentation card is usually the best solution for this process.
    Here’s our video on how to reinstall your GPU: https://www.youtube.com/watch?v=IqnY…ature=youtu.be

    1 beep too long and 3 short beeps – AGP does not work
    The video card may not be recognized and the first thing you should try is reinstalling it. Hopefully, insert the product back into the general sql error i/o error for file snugly enough. Ami bios error beeps, call us with a diamond, as we will check the map ourselves.

    Why is my Gigabyte motherboard beeping?

    This beep is usually caused by a faulty expansion card or motherboard that has stopped working. If that doesn’t work, reinstall and replace the expansion cards. Finally, you may encounter a serious problem, for which you need to contact us to find an RMA.

    1 long beep and short beep • memory error
    Please re-insert the RAM keys or try them individually to see if any of the keys are faulty. In this case, the system should function normally without the specified key, which must be replaced.

    Why is my Gigabyte motherboard beeping?

    This beep is always triggered, unfortunately, by a faulty expansion card or motherboard, which experts say has stopped working. If that doesn’t work, reinstall or practically replace the expansion cards, ami bios error beeps. At the end of the day, you may run into a major issue that you need to contact for an RMA.

    Beep long enough • Memory is not installed correctly
    Please re-insert the RAM keys or try male and female keys in turn to ami bios error beeps sure any key is not correct.n. In this case, the system should work without a USB flash drive, which then needs to be replaced.

    What does 5 short beeps indicate?

    Continuous single beep : no feeding
    Unfortunately, nothing helps, which is limited to replacing the power supply. For now, just give us a call.

    AMI BIOS
    American Megatrends Incorporated is an American hardware and ami bios error beeps company specializing in PC hardware and software. You benefit from your own beep codes:

    1 fast beep – memory error
    Please re-insert the RAM keys or try them to see if any of the keys are faulty. If that is the case, the system should not work as expected, Stick said, who would then suffer from the swap.

    How do I turn off the beep sound in my BIOS Gigabyte?

    There is nothing in the BIOS to disable post-beep, ami bios error beeps. Obviously turn off the internal speaker if possible.

    2 short beeps in case of tie presence : memory check error
    Reinstall the memory.
    Make sure the memory contacts are clean, as is the power outlet.
    Try to remove only one memory bank from modules ami bios error beeps a reliable time. (Some systems may require a specific memory module in bank 0, seeYour leadership)
    Test memory with modules far from the same manufacturer with a specific part number and speed.
    Check for a large, ami bios error beeps memory module by testing a known good system that is currently in memory.

    3 short beeps • 64KB of base storage competes with checkmark
    Memory reset error.
    Make sure the reminder contacts and sockets are clean.
    Try to clear the module bank at a specific time. (Some systems may use memory from bank 3, see your manual)
    Test the memory with devices from the same manufacturer with your current part number and speed.
    Check for a faulty memory module by creating a known high quality system in the memory.

    4 short beeps – real time clock malfunction.
    This is a tricky task, and it is helpful for most people to reinstall both the CMOS battery and graphics card.

    5 short beeps • Processor failure
    The central processing unit at the heart of your system is the lifeIt is an essential location and we do not recommend that you reinstall it at home. Call us, we may need to send your system in for repair.

    bios error beep codes gigabyte

    6 short beeps – keyboard error
    This beep dimming code is usually caused by a faulty expansion card or motherboard that has stopped working. If that doesn’t work, ami bios error beeps, just reinstall or replace the expansion cards. After all, you may be dealing with an authorization so severe that you need to contact us to obtain an RMA.

    7 Limited Beep – Processor Interrupt Error
    This Error0x5 at dtcping.cpp @303 beep code can be caused by an add-in card problem, system board, hardware problem, or processor damage. Replacing the faulty device that is causing the problem is usually the complete solution to this beep.

    Approved: ASR Pro

    Introducing ASR Pro- the world's most advanced and comprehensive PC repair software. Whether your computer is running slowly, experiencing errors, or just not performing as well as it used to, ASR Pro can help. This powerful application quickly diagnoses common problems and repairs them with a single click. You'll enjoy maximized performance, protection from data loss and file corruption, and peace of mind knowing ami bios error beeps your computer is now safe and error-free. Try ASR Pro today!


    Rare 8-tone video card with error
    This beep is usually caused by a faulty graphics card. Replacing the SD video card usually solves this problem, but in the end, before error pragma synchronous=normal a new card, you need to make sure thatbut it is actually installed in the expansion slot. Sometimes this AMI beep is a code from a loose card.
    Here’s our online guide to resetting the GPU: https://www.youtube.com/watch?v=IqnY…ature=youtu.be

    9 short beeps :Memory Gaffe
    You can try clearing CMOS first. If you’re lucky, it will make the task easier. Literally, this item will indicate a problem with the BIOS chip on the motherboard. However, we do not recommend that you “mess” with your business in At bios all. Call us!

    10 short beeps – CMOS error
    This beep is usually caused by a hardware issue in the AMI BIOS chip. Replacing the ami bios error beeps usually solves this problem, although in some highly desirable situations, a damaged expansion card may be the cause. Again, ami bios error beeps, this is what you constantly urge us to do.

    11 General beep for processor cache malfunction
    Eleven short beeps indicate that the cache check has failed. Typically, these AMI BIOS beep rules are used on any major failureour equipment, ami bios error beeps. This is often the motherboard.

    Get error sending on udp 0x2741 best performance from your computer with this software - download it and fix your PC today.

    Bios 오류 비프음 코드 기가바이트
    Bios Error Codigos Ami bios error beeps Sonido Gigabyte
    Codici Bip Di Errore Del Bios Gigabyte
    Kody Dzwiekowe Bledow Bios Gigabajt
    Bios Erro Codigos De Bipe Gigabyte
    Bios Oshibka Gudok Kody Gigabajt
    Bios Fout Piep Codes Gigabyte
    Codes Sonores D Erreur Du Bios Gigaoctet
    Bios Fel Pipkoder Gigabyte
    Bios Fehler Beep Codes Gigabyte

    3200mhz ramamiaorusasusasus motherboardaward biosb365m ds3hbootcomputerdual channelga 8ipe775ga bx2000gigabyte aorusgigabyte x570 aorus eliteramz390

    Computer POST and beep codes

    Beep CodeDescription and what to check1-1-1-1Unconfirmed beep code. Reseat RAM chips or replace RAM chips as possible solution.1-1-1-3Verify real mode.1-1-2-1Get CPU type.1-1-2-3Initialize system hardware.1-1-3-1Initialize chipset registers with initial POST values.1-1-3-2Set in POST flag.1-1-3-3Initialize CPU registers.1-1-4-1Initialize cache to initial POST values.1-1-4-3Initialize I/O.1-2-1-1Initialize power management.1-2-1-2Load alternate registers with initial POST values.1-2-1-3Jump to UserPatch0.1-2-2-1Initialize keyboard controller.1-2-2-3BIOS ROM checksum.1-2-3-18254 timer initialization.1-2-3-38237 DMA controller initialization.1-2-4-1Reset programmable interrupt controller.1-3-1-1Test DRAM refresh.1-3-1-3Test 8742 keyboard controller.1-3-2-1Set ES segment to register to 4 GB.1-3-3-1Autosize DRAM.1-3-3-3Clear 512 K base RAM.1-3-4-1Test 512 base address lines.1-3-4-3Test 512 K base memory1-4-1-3Test CPU bus clock frequency.1-4-2-4Reinitialize the chipset.1-4-3-1Shadow system BIOS ROM.1-4-3-2Reinitialize the cache.1-4-3-3Autosize cache.1-4-4-1Configure advanced chipset registers.1-4-4-2Load alternate registers with CMOS values.2-1-1-1Set initial CPU speed.2-1-1-3Initialize interrupt vectors.2-1-2-1Initialize BIOS interrupts.2-1-2-3Check ROM Copyright notice.2-1-2-4Initialize manager for PCI options ROMs.2-1-3-1Check video configuration against CMOS.2-1-3-2Initialize PCI bus and devices.2-1-3-3Initialize all video adapters in system.2-1-4-1Shadow video BIOS ROM.2-1-4-3Display Copyright notice.2-2-1-1Display CPU type and speed.2-2-1-3Test keyboard.2-2-2-1Set key click if enabled.2-2-2-3Enable ami bios error beeps for unexpected interrupts.2-2-3-3Display prompt Press F2 to enter SETUP.2-2-4-1Test RAM between 512 and 640 k.2-3-1-1Test expanded memory.2-3-1-3Test extended memory address lines.2-3-2-1Jump to UserPatch1.2-3-2-3Configure advanced cache registers.2-3-3-1Enable external and CPU caches.2-3-3-3Display external cache size.2-3-4-1Display shadow message.2-3-4-3Display non-disposable segments.2-4-1-1Display error messages.2-4-1-3Check for configuration errors.2-4-2-1Test real-time clock.2-4-2-3Check for keyboard errors.2-4-4-1Set up hardware interrupts vectors.2-4-4-3Test coprocessor if present.3-1-1-1Disable onboard I/O ports.3-1-1-3Detect and install external RS232 ports.3-1-2-1Detect and install external parallel ports.3-1-2-3Re-initialize onboard I/O ports.3-1-3-1Initialize BIOS data area.3-1-3-3Initialize extended BIOS data area.3-1-4-1Initialize floppy controller.3-2-1-1Initialize hard disk controller.3-2-1-2Initialize local bus hard disk controller.3-2-1-3Jump to UserPatch2.3-2-2-1Disable A20 address line.3-2-2-3Clear huge ES segment register.3-2-3-1Search for option ROMs.3-2-3-3Shadow option ROMs.3-2-4-1Set up Ami bios error beeps Management.3-2-4-3Enable hardware interrupts.3-3-1-1Set time of day.3-3-1-3Check key lock.3-3-3-1Erase F2 prompt.3-3-3-3Scan for F2 key stroke.3-3-4-1Enter CMOS setup.3-3-4-3Clear in POST flag.3-4-1-1Check for errors3-4-1-3POST done, ami bios error beeps, prepare to boot operating system.3-4-2-1One beep.3-4-2-3Check password (optional).3-4-3-1Clear global descriptor table.3-4-4-1Clear parity checkers.3-4-4-3Clear screen (optional).3-4-4-4Check virus and backup reminders.4-1-1-1Try to boot with INT 19.4-2-1-1Interrupt handler error.4-2-1-3Unknown interrupt error.4-2-2-1Pending interrupt error.4-2-2-3Initialize option ROM error.4-2-3-1Shutdown error.4-2-3-3Extended block move.4-2-4-1Shutdown 10 error.4-3-1-3Initialize the chipset.4-3-1-4Initialize refresh counter.4-3-2-1Check task 29 error 266 forced flash.4-3-2-2Check HW status of ROM.4-3-2-3BIOS ROM is OK.4-3-2-4Do a complete RAM test.4-3-3-1Do OEM initialization.4-3-3-2Initialize interrupt controller.4-3-3-3Read in bootstrap code.4-3-3-4Initialize all vectors.4-3-4-1Boot the flash program.4-3-4-2Initialize the boot device.4-3-4-3Boot code was read OK.Two-tone sirenLow CPU fan speed, voltage level issue.

    If your computer beeps and fails to boot

    On startup, computers perform a Power-on Self Test, commonly referred to as a POST. If problems are found while booting, you can usually diagnose them using the error codes displayed on the screen. However, if nothing displays on the screen, the computer might use sounds (that is, beep codes) to tell you what is wrong. Many of these errors indicate hardware problems that a service technician should fix. However, some errors are easily fixed. For example, keyboard controller errors often mean that your keyboard isn't plugged in.

    Following are beep codes for some ami bios error beeps brands of BIOS for PCs. For information about Mac beep codes or startup tones, see Apple Support's About Mac computer startup tones.

    Note:

    Many BIOSes will have different beep codes even if they appear to be from the same manufacturer. This is because motherboard manufacturers reprogram codes to reflect their own customizations. You can often go to the website for the motherboard's manufacturer to find the updated codes, ami bios error beeps, but you may find error 21 selected disk not exist windows where the manufacturer simply does not document the changes.

    For more about beeps and error codes, see ComputerHope.com's Computer POST and beep codes.


    Award

    Award BIOSes typically use more screen errors than beep codes.

    For Award BIOSes manufactured by Phoenix Technologies, note the following from the Phoenix Technologies AwardBIOS Error Messages page:

    "The only AwardBIOS beep code indicates that a video error has occurred and the BIOS cannot initialize the video screen to display any additional information. This beep code consists of a single long beep followed by two short beeps. Any other beeps are probably RAM (Random Ami bios error beeps Memory) problems."

    Award BIOSes not manufactured under Phoenix Technologies use the following beeps; this information is from the BIOS Central Award BIOS Beep Codes page:

    Beeps Meaning
    1 long, 2 short

    Video adapter error: Bad or improperly seated video card

    Repeating beeps

    Memory error: Bad or improperly seated RAM

    1 long, 3 short

    Bad video RAM or video card not present

    High-frequency beeps Overheated CPU: Check fans
    Repeating high/low beeps

    CPU: Improperly seated or defective CPU

    AMI (American Megatrends)

    The information below is from the BIOS Central AMI BIOS Beep Codes page.

    Beeps Meaning
    1 short DRAM refresh failure
    2 short

    Parity circuit failure in the first 64 KB of RAM: Likely a bad RAM IC, or possibly one of the hardware tests has failed error_message in sql2000 short

    Memory failure in the first 64 KB of RAM: Likely a bad RAM IC

    4 short

    System timer failure: Bad clock IC or bad RAM in the first bank of memory

    5 short

    Processor failure: The CPU has failed.

    6 short

    Keyboard controller Gate A20 error: The keyboard controller has failed. Due to its integration into the system board, you usually must replace the motherboard.

    7 short

    Virtual mode exception error: CPU has generated an exception error; bad CPU or motherboard

    8 short

    Display memory Read/Write test failure: Bad video card

    9 short

    ROM BIOS checksum failure: BIOS is defective

    10 short

    CMOS shutdown Read/Write error

    11 short

    Cache Memory error: Specifically, the L2 cache is bad.

    1 long, 2 short

    Video system failure: Error in video card BIOS, or a horizontal retrace has failed

    1 long, 3 short

    Conventional/Extended memory failure: RAM is bad

    1 long, 8 short

    Display/Retrace test failed: Video adapter is defective or missing

    AST BIOS

    The following information is from the BIOS Central AST BIOS Beep Codes page.

    Beeps Meaning
    1 short

    CPU register test failure: The CPU has failed.

    2 short

    Keyboard controller buffer failure: The keyboard controller has failed.

    3 short

    Keyboard controller reset failure: The keyboard controller has failed or the motherboard circuitry is faulty.

    4 short

    Keyboard communication failure: Bad keyboard controller or keyboard

    5 short

    Keyboard input failure: The keyboard controller IC has failed.

    6 short

    System board chipset failure: The chipset on the motherboard has failed. Replace the motherboard.

    9 short

    BIOS ROM checksum error: The BIOS ROM has failed. If possible, replace the BIOS on the motherboard.

    10 short

    System timer test failure: The system clock IC has failed.

    11 short

    ASIC failure: Motherboard circuitry has failed. Replace the motherboard.

    12 short

    CMOS RAM shutdown register failure: The real-time clock/CMOS IC failed. Replace the CMOS or motherboard.

    1 long

    DMA controller 0 failure: The DMA controller IC for channel 0 has failed. If possible, replace the IC.

    1 long, 1 short

    DMA controller 1 failure: The DMA controller IC for channel 1 has failed. If ami bios error beeps, replace the IC.

    1 long, 2 short

    Video vertical retrace failure: The video adapter ami bios error beeps probably failed. Replace the video adapter.

    1 long, 3 short

    Video memory test failure: The video adapter's memory has failed. Replace the video adapter.

    1 long, 4 short

    Video adapter failure: The video adapter has failed. Replace the video adapter, ami bios error beeps.

    1 long, 5 short

    64 KB memory failure: A failure has occurred in the base 64 KB of memory. If possible, ami bios error beeps, ami bios error beeps the RAM IC.

    1 long, 6 short

    Unable to load interrupt vectors: The BIOS was unable to load the interrupt vectors into memory.

    1 long, 7 short

    Unable to initialize video: This is a video problem. Replace the video adapter first. If the problem ami bios error beeps, replace the motherboard.

    1 long, 8 short

    Video memory failure: There is a failure in the video memory. Replace the video adapter first. If the problem persists, replace the motherboard.

    Compaq

    The following information is from the BIOS Central Compaq BIOS Beep Codes page.

    Beeps Meaning
    1 short

    No error: The system is booting properly.

    1 long, 1 short

    BIOS ROM checksum error: The contents of the BIOS ROM do not match the expected contents. If possible, reload the BIOS from the PAQ.

    2 short

    General error: No specifics available on what this code means

    1 long, 2 short

    Video error: Check the video adapter and make sure it's seated properly. If possible, ami bios error beeps, replace the video adapter.

    7 beeps (1 long, 1 short, ami bios error beeps, 1 long, 1 short, pause, 1 long, 1 short, ami bios error beeps, 1 dsn 5.6.0 data format error

    AGP video: The AGP video card is faulty. Reseat the card or replace it outright. This beep pertains to Compaq Deskpro systems.

    Continuous beep

    Memory error: Bad RAM; replace and test

    1 short, 2 long

    Bad RAM: Reseat RAM, then ms access error 2102 replace RAM if failure continues.

    Phoenix

    The following information applies to Phoenix BIOS Q3.07 or 4.x. This information is from the Phoenix BIOS beep codes section of the ComputerHope.com Computer POST and beep codes page.

    Dashes indicate pauses between beeps.

    Beeps Meaning
    1-1-1-3 Verify real mode, ami bios error beeps.
    1-1-2-1 Get CPU type.
    1-1-2-3 Initialize system hardware.
    1-1-3-1

    Initialize chipset registers with initial POST values.

    1-1-3-2 Set in POST flag.
    1-1-3-3 canon error code e007 CPU registers.
    1-1-4-1

    Initialize cache to initial POST values.

    1-1-4-3 Initialize I/O.
    1-2-1-1 Initialize Power Management.
    1-2-1-2

    Load alternate registers with initial POST values.

    1-2-1-3 Jump to UserPatch0.
    1-2-2-1

    Initialize keyboard controller.

    1-2-2-3 BIOS ROM checksum
    1-2-3-1 8254 timer initialization
    1-2-3-3

    8237 DMA controller initialization

    1-2-4-1

    Reset Programmable Interrupt Controller, ami bios error beeps.

    1-3-1-1Test DRAM refresh.
    1-3-1-3

    Test 8742 Keyboard Controller.

    1-3-2-1

    Set ES segment to register to 4 GB.

    1-3-3-128 Autosize DRAM.
    1-3-3-3Clear 512 KB base RAM.
    1-3-4-1

    Test 512 KB base address lines.

    1-3-4-3Test 512 KB base memory.
    1-4-1-3Test CPU bus-clock frequency.
    1-4-2-4Reinitialize the chipset.
    1-4-3-1Shadow system BIOS ROM.
    1-4-3-2Reinitialize the cache.
    1-4-3-3Autosize cache, ami bios error beeps.
    1-4-4-1

    Configure advanced chipset registers.

    1-4-4-2

    Load alternate registers with CMOS values.

    2-1-1-1Set Initial CPU speed.
    2-1-1-3Initialize interrupt vectors.
    2-1-2-1Initialize BIOS interrupts.
    2-1-2-3Check ROM copyright notice.
    2-1-2-4

    Initialize manager for PCI Options ROMs.

    2-1-3-1

    Check video configuration against CMOS.

    2-1-3-2

    Initialize PCI bus and devices.

    2-1-3-3

    Initialize ami bios error beeps video adapters in system.

    2-1-4-1Shadow video BIOS ROM.
    2-1-4-3Display copyright notice.
    2-2-1-1Display CPU type and speed.
    2-2-1-3Test keyboard.
    2-2-2-1Set key click if enabled.
    2-2-2-356 Enable keyboard.
    2-2-3-1

    Test for unexpected interrupts.

    2-2-3-3

    Display message "Press F2 to enter SETUP".

    2-2-4-1

    Test RAM between 512 and 640 KB.

    2-3-1-1Test expanded memory.
    2-3-1-3

    Test extended memory address lines.

    2-3-2-1Jump to UserPatch1. visual c+ + runtime error 1c
    2-3-2-3

    Configure advanced cache registers.

    2-3-3-1

    Enable external and CPU caches.

    2-3-3-3Display external cache size.
    2-3-4-1Display shadow message.
    2-3-4-3

    Display non-disposable segments.

    2-4-1-1Display error messages.
    2-4-1-3

    Check for configuration errors.

    2-4-2-1Test real-time clock.
    2-4-2-3Check for sql server error 17065 errors. ami bios error beeps
    2-4-4-1

    Set up hardware interrupts vectors.

    2-4-4-3Test coprocessor if present, ami bios error beeps.
    3-1-1-1Disable onboard I/O ports.
    3-1-1-3

    Detect and install external RS232 ports.

    3-1-2-1

    Detect and install external parallel ports.

    3-1-2-3

    Re-initialize onboard I/O ports.

    3-1-3-1Initialize BIOS Data Area, ami bios error beeps.
    3-1-3-3

    Initialize Extended BIOS Data Area.

    3-1-4-1Initialize floppy controller.
    3-2-1-1

    Initialize hard-disk controller.

    3-2-1-2

    Initialize local-bus hard-disk controller.

    3-2-1-3Jump to UserPatch2.
    3-2-2-1Disable A20 address line, ami bios error beeps.
    3-2-2-3

    Clear huge ES segment register.

    3-2-3-1Search for option ROMs.
    3-2-3-3Shadow option ROMs.
    3-2-4-1Set up Power Management.
    3-2-4-3Enable hardware interrupts.
    3-3-1-1Set time of day.
    3-3-1-3Check key lock.
    3-3-3-1Erase "F2" message.
    3-3-3-3Scan for keystroke.
    3-3-4-1Enter SETUP.
    3-3-4-3Clear in-POST flag, ami bios error beeps.
    3-4-1-1Check for errors.
    3-4-1-3

    POST complete; prepare to boot operating system.

    3-4-2-1One beep.
    3-4-2-3Check password (optional).
    3-4-3-1

    Clear global descriptor table.

    3-4-4-1Clear parity checkers.
    3-4-4-3Clear screen (optional).
    3-4-4-4

    Check virus and backup reminders.

    4-1-1-1Try to boot with INT 19.
    4-2-1-1Interrupt handler error, ami bios error beeps.
    4-2-1-3Unknown interrupt error. ami bios error beeps
    4-2-2-1Pending interrupt error.
    4-2-2-3Initialize option ROM error.
    4-2-3-1Shutdown error.
    4-2-3-3Extended Block Move.
    4-2-4-1Shutdown 10 error.
    4-3-1-3Initialize the chipset.
    4-3-1-4Initialize refresh counter.
    4-3-2-1Check for Forced Flash.
    4-3-2-2Check HW status of ROM, ami bios error beeps.
    4-3-2-3BIOS ROM is okay.
    4-3-2-4Do a complete RAM test.
    4-3-3-1Do OEM initialization.
    4-3-3-2

    Initialize interrupt controller.

    4-3-3-3Read in bootstrap code.
    4-3-3-4Initialize all vectors. ami bios error beeps
    4-3-4-1Boot the Flash program.
    4-3-4-2Initialize the boot device.
    4-3-4-3Boot code was read okay.

    IBM Desktop

    Beeps Meaning
    No beep

    No power, loose expansion card (ISA, PCI, or AGP), a short, or an improperly grounded motherboard

    1 short System okay
    1 long

    Video/display problem; video card incorrectly seated or defective

    2 short

    POST Error displayed on monitor

    3 long

    Problem with 3270 keyboard card

    1 long, 1 short Problem with system board
    1 long, 2 short

    Problem with display adapter (MDA, CGA)

    1 long, 3 short Problem with EGA
    Repeating short beeps

    Problem with power supply or system board

    Continuous beep

    Problem with power supply or system board

    IBM ThinkPad

    Beeps Meaning
    Continuous beeping System board failure
    1 beep with blank display

    LCD connector problem, LCD backlight inverter failure, video adapter failure, or LCD assembly failure

    1 beep w/message "Unable to access boot source"

    Boot device failure or bad system board

    1 long, 2 short

    System board, video adapter, or LCD assembly failure

    1 long, 4 short Low battery voltage
    1 beep every second Low battery voltage
    2 short w/message

    Read the error message on the display

    2 short with blank display ami bios error beeps board failure

    Mylex

    Beeps Meaning
    1 Normal boot: No problems
    2

    Video adapter error: Video adapter is not seated or is faulty

    3

    Keyboard controller error: Keyboard controller IC bad

    4

    Keyboard error: Keyboard itself might be bad, or the controller IC on the motherboard

    5

    PIC 0 error: The programmable interrupt controller IC is bad

    6 PIC 1 error: Same as above
    7

    DMA page register error: DMA controller IC is bad

    8 RAM refresh error
    9 RAM data error
    10 RAM parity error
    11

    DMA controller 0 error: DMA controller IC for channel 0 has failed

    12 CMOS RAM error: Bad CMOS RAM
    13

    DMA controller 1 error: DMA internal server error datalife IC for channel 1 has failed

    14

    CMOS RAM battery error: Dead CMOS battery; can usually be replaced

    15

    CMOS RAM checksum error: CMOS RAM failed

    16

    BIOS ROM checksum error: BIOS RAM failed

    Quadtel BIOS

    The following information is from the BIOS Central Quadtel BIOS Beep Codes page.

    1 short

    Normal boot: System is booting normally.

    2 short ami bios error beeps IC error: The CMOS RAM is faulty. Replace the IC if possible.

    1 long, 2 short

    Video failure: The video adapter is faulty. Reseat the video adapter or replace the adapter if possible.

    1 long, 3 short

    Peripheral controller error: One or more of the system peripheral controllers is bad. Replace the controllers and retest.

    0 Comments

    Leave a Comment